netgear 8 port switch 3d models

The Netgear GS108 can be securely fastened onto any wall or surface using command strips, ensuring no damage is done to the device. ...Its compact design consists of two interlocking parts, ideal for use with the M3D Micro's limited build area.

I designed this simple wall mount for the Netgear GS108 8-port switch because I believe its original mounting method is very frustrating. It takes a long time to get the nails or screws precisely into place to secure the switch. Furthermore, you...

I wanted to clear some desk space by removing my Netgear GS108 8-Port Switch from the desk. The Ethernet cable layout on the desk was cumbersome, so I decided to turn the switch with its ports facing the wall - the cables came up from below and...

This is a mounting bracket designed specifically for securing an eight-port Netgear switch, such as those from the GS108 series, underneath a desktop. The bracket features attachment points that align perfectly with the existing screw holes at the...

There are lugs that fit the bottom screw holes of the switch. It also has hooks to clip in the cables to keep it somewhat tidy.</p><p>If you have a 200x200 build plate like me then rotate it 45° in the slicer to keep it away from the edges of the...

... mounted beneath a table, on a wall, or any other location where two screws can be securely fastened. For those seeking an identical holder for the five-port switch, please visit Thingiverse and search for the model with identifier 3388238.

... pattern to it. ...The switch can be mounted under a table, on the wall or wherever you can fit 2 screws in it If you are looking for the same holder for the 5 port switch: https://www.thingiverse.com/thing:3388238 Print instructionsCategory: Computer

The two mounting holes in these Netgear switches seem to be too tight to easily fit using M4 screws like the original design, so I made this reminx which use M3 screws to mount the switches. An M3x10mm screw and M3 nut (regular or locknut) will be...

This bracket holds a Netgear GS308 Ethernet switch to the underside of a shelf. Uses four wood screws to attach.</p> <h3>Print instructions</h3><p>I used PETG. PLA would probably work too. Print settings are not critical -- it didn't need support...

I'm upgrading the mounting system for Netgear Switches. These custom mounts were designed with a GS308 in mind, but haven't been thoroughly tested yet. The existing holes on the switches seem too small to securely attach using M4 screws like the...

Needed this wall mount to be printed on my tiny printer. ...So I seperated the mount and adjust it a little bit. With this adjustment you may use it for 5 port switch also You have to mirror the parts in your slicer, to get the Left and the right part!

<p>This is a remix of the design <a href="https://www.thingiverse.com/thing:1322695">https://www.thingiverse.com/thing:1322695</a>.</p><p><br>I seperated the model and added some support, so you can print it also on smaller printers and you are more...

Product page: https://www.netgear.com/business/wired/switches/plus/gs308e/

https://www.thingiverse.com/thing:3758304 This is a 1U space for two TP-Link TL-SG108 or Netgear GS308 8 port GigE switches. It also can take the TP-Link managed 8 port switch as well, which has the same form factor. There will be a remix with...

Thanks to the make by DasFasty for testing the M3 version! https://www.thingiverse.com/thing:3758303 This is a 1U space for two TP-Link TL-SG108 or Netgear GS308 8 port GigE switches. It also can take the TP-Link managed 8 port switch as well, which...

A cost-effective Gigabit switch with POE and VLAN was required; the Netgear GS108T met the criteria. However, it lacks rack-mount ears. Fortunately, here are the missing ears for you to use! ...Enjoy your improved switch setup.

Created for a snug fit, only fits over the face of this switch which stops it being able to fall through. ... Rotate object 45' to fit diagonally on bed as shown in Picture 2 Printed on Ender 3 Printed on 0.4mm layer height for speed 30% infil...

Fits my Phillips hue and Tado hubs and my 8 port network switch from Netgear. Printed in PLA. ...Used a brim to help with adhesion as the bottom is quite thin.

A 20mm tall and low profile 11.22mm tall mountable base with built-in cable channels allows you to route the patch cables under the switch, keeping it stable on a shelf/table, while still seeing the activity LEDs on the ports. Cable channels are...

... not just Netgear switches. They just need to have a screw mounting hole of ~6.5mm. Found on netgear 5 and 8 port switches.. if they are listed as "wall mountable", you should be golden. ... Print with a tiny selective support below the "screws".

Immediate Fulfillment Network\nNetgear Prosafe 24-Port Gigabit Unrestricted Switching System

This mount fits the 5-port Netgear GS305 gigabit switch, and various other devices from the same manufacturer share a similar chassis design. Two vertical mounting holes enable secure attachment with two screws into a stud, causing the connectors to...

Basic underdesk mount for holding a 5 port Netgear switch. ...Mounts via double sided taped, then secure using velcro.

Simple stand for a Netgear GS316. ...Should also work for Netgear or other Brands and Switches.

Due to lack of space I needed to stack two Netgear 16 port switches on top of each other, but wall mounted. The switches have wall mount holes individually, but not to stack on top of each other. This allows the second switch to be strapped on top of...

... almost anywhere you need it - under a table, on the wall, or wherever two screws will fit into place. ...If you're looking for the same holder but with an 8-port switch, check out this alternative design: https://www.thingiverse.com/thing:3278568

The switch can be mounted under a table, on the wall or wherever you can fit 2 screws in it If you are looking for the same holder for the 8 port switch: https://www.thingiverse.com/thing:3278568 Print instructionsCategory: Computer Print Settings...

The switch can be mounted under a table, on the wall or wherever you can fit 2 screws in it If you are looking for the same holder for the 8 port switch: https://www.thingiverse.com/thing:3278568 Print instructionsCategory: Computer Print Settings...

As my list of ongoing projects grows, I find myself constantly seeking a reliable spot for my Netgear Switches. I usually have 2 or 3 on hand. In the past, I had a couple of suitable mounting spots, but Velcro was no longer meeting my needs. With my...

IES-1080A Industrial unmanaged ethernet switch with 8x 10/100Base-T(X) ports by ORing. ...Power input: 12-48 VDC