net model

I based the design of these pieces off of the Ender 5+ model available on GrabCAD (https://grabcad.com/library/creality-ender-5-plus-1). There will eventually be a detailed pdf showing a build guide, confirmed material list, building and flashing...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

To use a different font than the standard Roboto (English) for either (or both) of the lines of text you just need to install the font onto your machine and configure it in the model parameters (in Customizer *locally* or in your .json file, more on...

*** I do not want to come across as an erse, so I'm sure some will think I am when I say this - but I want to clearly point out that this is a CC ATTRIBUTION - _NON-COMMERCIAL_ - _NON-DERIVATIVE_ license - please let's enjoy the model, but please...

I like you.text10 = ---textsizes = [13,13,13,13,8,8,8,10,6,10]Boat labeltext1 = Coast Guard Capacity Informationtext2 = ---text3 = Maximum persons|3text4 = Maximum gross load|100kgtext5 = Persons, motor & equip.|50 poundstext6 = Maximum...

Keep weight and cooling considerations in mind if using an alternate - ESC: Water proof ESC appropriately rated for your motor / battery combo - Cooling Nipple: M4 X L15 https://www.aliexpress.com/item/32614416689.html - Cooling Tube: 4 mm I.D 7 mm...

Both uploading and downloading a few dozen bricks is a pain :) However you can get all: STL.zip contains all the blocks I made so far STL-sets.zip include multiple brick sets for printing (difficult and not so often updated !) source.zip contains all...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

The files are prefixed with Updated_ or New_.Here are a couple videos of it running  Please refer to the Original model for assembly and any other sources.I have uploaded the file as a Fusion 360 archive folder so you will need Fusion 360, Fusion 360...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

 - INCOMPLETEAdd variation with looser tolerances so pots can rotate freely - INCOMPLETEAdd small washer to fix noise issues some have experiences - INCOMPLETE As with any of my models, feel free to message me with any questions or...

If you need a lot more room (more than a few mm) you may need to update the model to scale it appropriately. (~$1 of filament)</li> </ol> <ol> <li>Light string or rope. Cut it about 5ft 6 inches, or just enough to make a loop on the elbows, running...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

To prevent that, don't hesitate to rotate horizontally one the stack 90° clockwise or counter clockwise, to prevent symetric parts interlocking each other.More than two player can play together if another set of tiles is printed.The printsThe 3D...

Scaling up the model to increase the included printing gap, will stop it fusing if this occurs.Step 5Now to starting turning the collar back and forth to try and loosen it up. The box closes by twisting the upper collar anti-clockwise (this can be...

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

**Update 2022/04/08:** Fixed a bug in main body model. It was slightly to long on left bottom side to fit nicely over the antminer case. This project aims to convert a Bitcoin miner into a handy space heater. **We achieve this by:** *...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

But it works in the end ;)I hope this will help some people who own the same device !NB: You will need to adjust the slots in the 3d model according to the size of your battery contacts.&nbsp;2. Revision History</strong></h5><figure class="table"...

Externally modeled accurately from my real life Amiga 500+. Video of Doom Eternal on it: https://youtu.be/lsHi1vf_0Z4 Advanced project for builders that know how to fabricate some things like cables and adapt and paint parts to fit their hardware....