net cups hydroponics 3d models

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

I got tired of the net cups sitting all loose on top of the pipe so I designed a bezel the molded to the pipe and gave a flat surface for the net cup to sit on. I then hot glued them to the pipe. I later realized that if I added a additional inner...

I got tired of the net cups sitting all loose on top of the pipe so I designed a bezel the molded to the pipe and gave a flat surface for the net cup to sit on. I then hot glued them to the pipe. I later realized that if I added a additional inner...

Inspired by Aussie YouTuber Hoocho to try to grow some vegetables hydroponically, i built a small test setup with 90mm stormwater pipe commonly found here down under. After some success with drip fed buckets using inert soiless media and some...

I designed a net pot that prints effortlessly without any support structures. ...Other designs often omitted the bottom layer or included built-in supports to allow for printing, but this model can be fully printed with no supports whatsoever.

This is a 50mm or 2" diameter net cup designed for printing in vase mode. The resulting part will have a few holes in the bottom, and vents all around the sides where the vase mode leaves gaps at the tops of the little embossed rectangles. I have...

Wanted something better than a normal net cup to help my hydro pepper plants while they grow and have an option to tie to instead of the ceiling in my tent. Quickly added these poles to do so, the first version didn't have strong bottom connections...

I was seeking something more than a standard net cup to assist my hydro pepper plants as they grow and wanted an option to tie up instead of relying solely on the ceiling in my tent. I rapidly assembled these poles to meet this need, but the initial...

I aimed to craft some compact hydronet cups that harmonize perfectly with the affordable, galvanized 'bintje' IKEA pots, specifically those measuring 4 1/4 inches in diameter. ...The flexible TPU material proves ideal for adapting to the root systems,...

... is needed. Explore Xoodo Pod at https://www.thingiverse.com/thing:3433978 This design is not a remix, but rather an ode inspired by the fabulous Voronoi-inspired net pot. ...Kudos to the original creator at https://www.thingiverse.com/thing:523289.

Voronoi-inspired Net Pots/Planters for Xoodo Pod System, also applicable universally like IKEA Vaxer, measure 68x68 mm in size. Explore the overall concept of this design at www.xoodo.io to see how we're working towards automating agriculture as a...

First try of a model. ... Net cups in 4 different variations. ... - 52mm inner diameter (top) - 64mm outer (top) - 06mm edge (top) - depth 53mm Oh and do your cable management ( learned it the hard way :D - last picture )

Remix with less material

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

Customized version of https://www.thingiverse.com/thing:790339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=790339

I designed this Net Cup specifically for the Ebb Flow Hydroponics tower - https://www.thingiverse.com/thing:386377. It fits snugly and has been designed to solve the issue that the author said that he had with standard net cups - they tip as the...

The Hydroponic Net cup/Pot System is a game-changer for your 4" PVC Pipe setup. Begin by starting your plants in smaller net cups within a cloner or nursery. When it's time to transfer them to your 4" PVC pipe hydroponics system, simply attach the...

With this design my goal was to create a clean interface between the net cups and the PVC tubing. Note: This design is for v2 of my hydroponic grow which has not happened yet, I have not installed these yet, they are only a proof of concept...

Elevates your net cup upwards to get the most out of the space inside your nutrient solution container. Works best when installed on a fence post setup. I created this with the Kratky method in mind, but could probably be used in other applications.

... in other applications. This spacer will increase the height of your net cup by 40mm.To install, simply squeeze the sides near the clips and insert.Demonstration: https://www.youtube.com/watch?v=nBscKCo7DNo Print with supports, clips side up.