nest hello 35 degree wedge 3d models

Small modification of the 45 degree wedge that does not require heat-set insert nor iron to place it. Instead, it uses a standard furniture screw, which I bought on Amazon: 40Pcs Anwenk 1/4"-20 x 15mm Furniture Screw in Nut Threaded Wood Inserts...

This setup will cause your tail to move outward more than your nose during a turn, leading to highly unstable "speed wobbles." Also note: Stacking multiple Wedge Risers or stacking wedges with other accessories on the same truck is strongly...

Here's a Simple Wedge That Can Be Easily Added or Removed With a Strap For Your GoPro/Xiaomi Yi Or Other Action Camera.

I designed a 45 degree wedge to allow greater elevation angles on my camera when needed, due to my tripod head's limited vertical range of motion. Additional parts include: 1/4-20 brass heat set inserts for plastics (McMaster-Carr part no. Tools...

2) I measured the back of the head torch to create a 30 degree wedge to point it down more into your field of view, it perfectly fits the curved back of the torch and still gives you the same curved surface that presses against your forehead. ...

It incorporates a 5 degree tilt to the board, which is what I prefer, and that's about it.This is provided as 2 STL's, the center section, and the end part, which is mirrored in one instance to print for both sides. You should be able to print both...

Here is the rewritten text: This angle-defining GO Pro Wedge has solved my problem with my SPanKY Quad copter; since I am running an extreme, High Power Quad, no matter how fast or sharp I go, my video view will always be of the same old thing:...

Humans securely latch onto the nemesis's upper plate. ...Configurations compatible with GoPro and Mobius are accessible. A 20-degree adjustable tilt allows precise positioning.

... quadcopter. ...I highly recommend using this versatile attachment for your GoPro camera if, like me, you possess a high-power system; otherwise, be prepared to record nothing but lawn footage if you attempt to secure your device at zero degrees!

I installed a 30-degree bracket at the base of the enclosure, allowing for direct attachment to the quad via battery straps or equivalent securements. ...This eliminates the need for an additional printed mount.

The customized version of this model can be found at http://www.thingiverse.com/thing:57000, created using the Customizer app with a rise of 0, a tolerance of 0.5 and an angle of 17 degrees. ...For instructions on how to use the Customizer, visit...

35 degree session mount

Customized Version of Thingiverse Item Number 1015101 Generated with Customizer Tool: http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 User Instructions: Using the Following Parameters: * Base Thickness: Set to 2 Millimeters * Screw...

... that has a bigger wedge angle. So I designed this 35 degree adapter and it works pretty good. It needs M3 brass inserts for the Remo door bell to attach to it. ...I pushed the brass inserts out of the Remo flat adapter and epoxied them into this.

http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 Using the following options: Base thickness is set to 2 Screw head size is set to 6 Front and rear cross-sectional area is 49.5 Edge margin is precisely set at 3 Front cross-sectional...

35 degree bevel guide for https://www.thingiverse.com/thing:4626160

The 10 degree wedge that accompanies the Eufy 2k hardwired video doorbell doesn't provide an adequate perspective when the device is mounted at a perpendicular to the wall it's attached to. ...This 45 degree spacer offers a crystal-clear, straight-on...

http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 Instructions Using the following options: hole_size = 3.2 rear_cc = 30 solid_wedge = No edge_margin = 3 velcro_height = 3 base_thickness = 2 front_rear_cc = 49.5 velcro_width = 20 angle...

http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 Instructions Using the following options: rear_cc = 29 hole_size = 3.2 base_thickness = 2 angle = 35 velcro_width = 20 solid_wedge = No velcro_height = 3 front_rear_cc = 42 front_cc = 29...

Remixed from JoyMonkey's Runcam Mount. ...Source was available on onshape and I just changed the camera angle to 35 degrees.

The Dronewolf mount was thoroughly upgraded to provide superior support for session cameras, and the tilt was expertly adjusted to a precise angle of approximately 35 degrees.

Quick remix I did of the model by Zaros. ...I just angled the part that holds the PTFE tube at a 35 degree angle. ...I'm using it in my Voron Trident as a guide for my internal spool holder.

Pilots are installing a specialized 35-degree FPV mount designed specifically for the high-resolution Fatshark 600 TVL camera, which is being mounted on a sturdy ZMR 250 quadcopter frame.

http://www.thingiverse.com/apps/customizer/run?thing_id=1015101 Instructions Using the following options: screw_head_size is set to 6 hole_size has been adjusted to 3.2 front_rear_cc measures in at 48 base_thickness stands at 2 front_cc comes out to...

... ...What I need is a sturdy and sleek accessory that securely fastens onto my bike at a slight angle of 35 degrees. ...The GoPro Mount, specifically designed with this in mind, allows me to capture dynamic footage without sacrificing stability or style.

The user adjusts a fan to point directly towards the wall at a precise angle of 35 degrees. ... This setup is specifically designed to effectively cool drives housed within a wall-mounted camera server, ensuring optimal performance and preventing...

This 35 degree shim gives a perfect angled view. Print instructionsSince this is intended for outdoor use, I'd suggest printing in PETG. ...It doesn't need much infill, and you can set the bottom layers to 0 as I've shown in the 3mf and example...

these tents were the flat rest from chewiedies tilted 35 degrees, then optimized for printing with flat portion on the inside facing down on the bed. you shouldn't need any supports, mine printed with abs at 10% and came out well. ... mirror for...

http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following settings: Increment to 10 units Starting at position 5 Spine width set to 4 units Type chosen is floating Width and height both set to 4 units Ending at...

Here is rewritten text: I based my jocampo QAV210 mount with a 35-degree uptilt.\nModifications\n1. I added a lip to keep the velcro strap securely in place\n2. I installed slots to allow tools easy access to the screws\n3. I modified the mounting...