nero 3d

Remove the z-axis tops and replace with this light bar mount. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired...

Possibly by using simulations.Rails as a wholeSince my 3d printer is not big enough to fit 120cm ring on it (its bed is 210x250mm) I needed to split rails for printing and connect them afterwards. I decided on using M5 bolts and nuts.</p><figure...

Worlds are waiting.Equip yourself today, citizen!Space Port - https://www.printables.com/model/205432-space-port-terrain&nbsp;Starship Cargo Pod - https://www.printables.com/model/224797-starship-cargo-pod&nbsp;Starship Transfer Tug -...

I made it 11mm to account for any tolerance issues caused by the 3d printing process and to allow wiggle room for perfect alignment. If you are using a different switch and want to remove the plate recess or modify the through-hole size, I have...

This is a followup to: Lack Attack#3: Koppla the Lack: https://www.prusaprinters.org/prints/15919-lack-attack-3-koppla-the-lack-aka-power-the-lack-s without further adieu.... Attack 4: ENCLOSE THE LACK Its been a while since my last update, mostly as...

These strips are bright enough I didn't notice only one was on. View from Octoprint Control tab during the first layer of my first print after installing. Print instructionsCategory: 3D Printer Accessories Summary Prusa i3 MK3 PiCam v2 X-Axis Motor...

Or, see the retainer tool below for a 3D printed solution to this potential problem  Retainer ToolHave you been a victim of the Domino Effect causing all of your lights to end up on the ground? Are you worried you could be? Well fear no more! The...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

If you don't own a 3D printer but have seen this blank somewhere else and want to use it, I recommend just asking in a furry group chat on a platform of your choice. Many furries are also tinkerers and may print this for little money.</p><p>The base...

Use thread lock to ensure these will not accidentally come loose.A 36mm diameter propeller should run freely inside the rudder at all rudder angles.Mount the rudder support to the hull using M3x6mm screws.Then put another M3x6 screw to secure the...

It appears to be a set of points in 3D space represented using an [Hull format](https://docs.python.org/3/library/pickle.html#pickling-hints). I will assume you'd like me to convert this into some kind of array. However, there are no "lines" or...

... at 0.2 layer height.</p> <p>But once you've raised the limits, it's worth seeing what a 350mm/s travel move really looks like at 5500 or 6000 mm/s^2. (Answer: sorta scary, honestly) Designed from scratch in SketchUp. Category: 3D Printer Accessories

Note that if there is more than one row or column, the row or column spacing still will be applied (which can be useful to match a specific size).An optional area for adhesive label (which IMHO work better than adding a 3D printed text). It's...

(Support Enforcers Only)Multiple Modules:Dual floor module - Space-Port-Residence-NW-R-V1 and Space-Port-Residence-NW-L-V1Standard module with connecting walkways - Space-Port-Residence-R-V1 and Space-Port-Residence-L-V1Additional walkway to bridge...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above.&nbsp;Support enforcers are neededNo gluingEasy to printDesigned on...

Worlds are waiting.&nbsp;Designed on Tinkercad.Enforced supports are required on overhangs and the main bodies (see 3mf files).The main bodies can be glued together to create longer Cargo Pods.Super glue everything together.Start shipping cargo; the...

All of the unnamable, unfathomable endless universes constantly branching as Hugh Everett described in the mid 1950's.&nbsp;This is the place where gods are created.The Original Galindos -...

I present to you, what is likely one of the only mechanically working 3d-printed Prop Revolvers available, especially for free!Go here to see it in Operation: https://i.imgur.com/DBUVUkF.gifvIt is quite well balanced, see here:...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

His diagrams and commentary on escapement efficiency were excellent, however.&nbsp;I only discovered this write up on escapement design after I'd finished, but it would also be a useful head start for anyone interested -...

Just to make it easier finding it all in one place.No support required.Diesel Generator you will need to superglue the bottom frame (very simple)Designed on...

What to print: Print these files: icarus-1.2.1-for-sherpa-mini-r1-normal.stl sherpa-mini-r1-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl...

There are plenty of good tutorials on that topic (including 3D printer mods adding Noctua fans with buck converters) so I have no intention to create another one here. You may need tools like a soldering iron and a multimeter to get the job done.The...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

Remove the stock z-axis tops and replace with this light bar mount.Single Mount Z-Axis Top No Switch: Same as Single Mount Z-Axis Top with no hole for the power switch.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15%...

Use with Right MMU2 Mount Z-Axis Top.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired hardware:Aluminum u-channel24V...

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

If you want to add time indicators to the watchface I'd recommend using roman or greek statues holding the numbers, to fit the theme.&nbsp;UPDATE: I've added a few statues with numbers to make reading the clock a little easier, they are based on the...

It looks better when printed at that size.Print out and assemble with superglue.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...