nerf tactical rail accessories 3d models

This is the horizontal and vertical Nerf Accessories Rail Mounts. 2 pieces each, hook is separate (and universal to all my pegboard products). 75mm long Nerf rail Print in PETG for a durable and long-lasting finish. TERMS: Once you buy these...

I prefer my current design but appreciate the idea of giving it a bit more breathing room underneath the rail.

I built this for my Rival Apollo, making sure the 12-round magazine wouldn't stick out in front and turn my gun into a unicorn. I wanted to keep things simple. Resolution isn't crucial, but infill should be around 50%. ...When attaching it to your gun,...

This creation originated on Tinkercad. ...You can refine it directly here: https://www.tinkercad.com/things/lzBZ9TjRwG5.

Designed this for my Rival Apollo. I didn't want my 12-round mag to hang off the front and make my gun a unicorn. :) Resolution doesn't matter too much, and infill should be about 50%. ... Make sure you glue it on your gun really well, or it will fall...

Create Custom 3D Nerf Rail Systems with Ease.

This tiny connector simply connects two tactical rails from two different Nerf guns (or blasters) together. So you always have a spare weapon at hand. A print lasts only 15 minutes, create two of them. No, I didn't connected them for a couple of...

This is a nerf rail attachment that holds 5 extra nerf darts and because the original design blocked your view I added an iron sight in the center. It is remixed from asworx's design because I used their rail clip to attach it to the gun. ...Thanks a...

I designed this to work perfectly with my printer's tolerances, but it may not be a good fit for you. I printed at 20 percent infill and the result is a snug fit. ...Printer Settings: Printer: Flashforge Creator Rafts: None Supports: None Infill: 20%

Parts has snug fit, up to the point where it need some “persuasion” with soft mallet to go over locking lug.Yes, it's print on 45 degrees with very little contact with bed, so brim is recommended.Two versions:Normal 2.2 inch 5 slots railShortened 1.8...

So I designed a simple sight to be mounted on the tactical rail of the gun. It prints seamlessly without support required. ...I printed it in bright orange PLA (with layer height set at 0.2 mm, three perimeters and 25% infill) using my ReprapPro Huxley.

... invisible during daylight hours. ...So I designed a simple sight to be attached to the "tactical rail". It prints smoothly with no supports needed. ...I printed it in orange PLA (layer height: 0.2 mm, 3 perimeters, 25% infill) on my ReprapPro Huxley.

... ...So I designed a basic sight to be mounted on the "tactical rail." It prints quickly with no support required. ... I printed it in bright orange PLA (layer height: 0.2 mm, three perimeters, twenty-five percent infill) on my ReprapPro Huxley.

Parts has snug fit, up to the point where it need some “persuasion” with soft mallet to go over locking lug.Yes, it's print on 45 degrees with very little contact with bed, so brim is recommended.Two versions:Normal 2.2 inch 5 slots railShortened 1.8...

I designed a rail system for Nerf guns because my brother is a huge fan and he said he needed more space for scopes, handles, and other attachments. So, I came up with a solution and printed it out. Print Settings: Printer Brand: RepRap Printer...

These tactical rails slide right onto your factory setup. The charging handle needs a 47mm M3 with nut, which goes behind the factory rear sight to lock it in place, preventing it from moving forward. I designed this for my K-26 spring upgrade since...

https://www.tinkercad.com/things/4NA3S0qNgZH I designed a tactical mount for mini-maglite. Enjoy! Print Settings Printer Brand: Printrbot Printer: Simple White Rafts: None Supports: None Resolution: 0.1mm Infill: 20% Notes: This model was actually...

I just happened to wake up one morning with a sudden urge to slap a scope onto something that gives you a real kick, so here's the result.

The switching out of the slap from the foam fist.

This pump is a fusion of its original components and two distinct influences that have been merged seamlessly together.

Use this design to attach something to the top. Scope holders, dart racks, guns, or even sandwich makers are all possibilities! This model prints with no need for supports. However, it may require a bit of force to get it to fit properly. ... Special...

... for this job. Just be sure to fill any gaps with putty afterwards. Tamiya plastic putty and Milliput work great for this task. The SMG muzzle can be used either on its own or paired with a 25mm pipe as a mock barrel on a standard Nerf blaster.

tactical Nerf mag holder

This is a GoPro standard mount designed specifically to work seamlessly with the Nerf Tactical Rail system.

The design features a Nerf barrel with Picatinny rails replacing the standard Nerf rail, providing users with more flexibility in adding accessories such as scopes or flashlights. The fake cylinder, available on Thingiverse...

An additional trommel to fit 6 Nerf darts, to have them handy for fast reload. ... The trommel fit the tactical rail on most Nerf guns. Additional I made a stand/mount which can be used as desk or wall mount. ... Happy printing.

This simple tactical sight is designed for Nerf guns and fits the rails on most models. The V2 version comes with a locking pin at one end, giving users a more authentic look if desired. ...Assembly requires only gluing the smaller component to the...

Tactical Torch Mount for Nerf Elite Rails This print is a torch mount designed specifically for Nerf Rails, perfect for the zoomable 2000 Lumen LED Torches available on Amazon. To create this attachment, you'll need to gather the following parts: * 2...

bolt on nerf rail. put a spring under the rail catch, it shoult take 3mm or #4 american standard bolts. ...enjoty modders!

Bolt on a Nerf rail and install a spring underneath the rail's catch. This should be accomplished using either 3mm or #4 American Standard bolts. ...Enjoy modifying your devices, modders!