nerf modulus ecs 10 flywheel cage 3d models

This is a substitute top rail for the Nerf Modulus ECs-10, designed to connect the top carrying handle securely to the front rail system.

Voltmeter Mount for Nerf Modulus ECS-10 Replaces Cable Channel Two Versions Available: Holes or No Holes to Fit Different Sized Voltmeters Designed with Inspiration from Thingiverse's 2422841

This part securely closes the carry handle on the Nerf Modulus ECS 10, smoothly sliding into place along the two upper rails of the blaster. ...By doing so, it keeps the topmost rail largely accessible, allowing for a wide range of attachments to be...

This is a replacement Picatinny side rail for the Nerf Modulus ECS 10. To install, remove the existing rail and secure from front to back using two bolts, two washers, and M3 nuts (refer to third photo). Please note that this is licensed...

A Custom Wall Mount for a Nerf Modulus ECS-10 Blaster. Two parts make up each bracket, the mounting plate and the hook itself, to avoid needing supports. On my printer, I had to scale the X and Y dimensions up by 1.02 times to get them to fit...

A custom wall mount for a Nerf Modulus ECS-10 blaster. There are two parts to each bracket, the mounting plate and the hook itself, so as to avoid needing supports. On my printer I needed to scale the X and Y dimensions up by 1.02x in order to get...

A custom wall mount for a Nerf Modulus ECS-10 blaster. There are two parts to each bracket, the mounting plate and the hook itself, so as to avoid needing supports. On my printer I needed to scale the X and Y dimensions up by 1.02x in order to get...

This is a custom-made battery cover and front stock grip designed specifically for the Nerf N-Strike Modulus ECS-10. Print Settings Printer Brand: Prusa Printer Model: Prusa Clone Rafts: Yes Supports: Yes Resolution: 0.2mm Infill Density: 25% ...

Fixes the Nerf Clip Stock (Comes with the Modulus ECS-10) so that its not wobbly anymore. Spacers snap in. Since the end ones overlap the shell pieces; the insertion order matters. Mini-puzzle! The hole bored through the middle is a close match to...

The solution comes in the form of a Modulus ECS-10 modification that addresses this problem. To get the spacers to snap into place properly, you need to pay attention to the order in which they're inserted. Since the end ones overlap with the shell...

Wanted a bigger set of accent grips for the Modulus ECS-10. The left side uses the factory hole, just a longer screw. The right side will need to be drilled out from the left through right right side so that a screw can be used to secure that side as...

A versatile upgrade for the modulus side rail system, compatible with 180-size motors and empowering users to expand their creative possibilities.

I widened it a lot to cover up a huge hole I cut way too big in my Modulus ECS-10. I also shortened its posts some to help ease in printing. ...I designed this make to print with full support with the cover up, thus giving the best overall finished...

Extended magazine release designed for the Nerf Modulus ECS-10/Tracker. Replaces the original button and lever with a single piece that fits on the existing screw post. Five lengths available - 42mm, 47mm, 52mm, 57mm, 62mm. This is the distance...

Replacement unbranded battery door file for the Nerf Modulus ECS-10. If you have lost your original door then this will allow you to print yourself a replacement or maybe you have added a bunch of 3D printed parts and want your battery door to...

Replacement "FIB" Branded battery door file for the Nerf Modulus ECS-10. If you have lost your original door then this will allow you to print yourself a replacement or maybe you have added a bunch of 3D printed parts and want your battery door to...

I modified it to work with the Open Flywheel Project Modulus/Demolisher Flywheel Cage here: https://www.thingiverse.com/thing:2432285 I also created a custom skeleton trigger and lengthened the pusher extension lever, moving the fulcrum point closer...

MAY fit the "Demolisher" This is a modified Stryfe cage to fit the Modulus ESC 10. The changes were provided by Michael Ireland, so I want to give him a huge thanks for giving me his modifications to support the ECS-10. I don't have an ECS-10...

Upon closer inspection, I noticed that the Modulus_top_rail_Right_FrontHalf.stl file was slightly off in size compared to its counterparts. ...To rectify this issue, I utilized Blender's snap feature, which allowed me to quickly adjust the dimensions...

This is a custom-designed flywheel cage for Nerf Modulus or Nerf Demolisher enthusiasts. It's open-source and optimized for maximum performance. Four distinct versions of this cage design are available here, but to achieve the highest level of print...

This design replaces the half / open carry handle on the Nerf Modulus ECS-10 with a full handle that uses existing mount structure in back and rear portion of rail in front. Major bonus that you get a nice long rail -- both Picatinny- and Nerf-style...

Many people complain about the grip on the Modulus ECS-10 being uncomfortable because of the cutouts / sharp edges. These are simple inserts that press into the grip on either side to make the grip rounder. ...I find that they stay in well enough just...

This is my Modulus ECS-10 grip replacement with hinged trigger, rev trigger, and new mag catch/release. It is a direct replacement for the stock grip with minimal shell modifications. It includes space for a high current snap action switch and...

I designed this around the Nerf Modulus ECS-10. I got several on the cheap and made one for my middle boy when he was obsessed with Pink Fong. All these parts have been tested and vetted and should be good to go. These are not for re-sale or...

High-torque flywheel cage engineered specifically for high-performance Nerf guns utilizing robust 12-volt DC brushed motors.

With its sleek and ergonomic grip, the Nerf ECS-10 Pusher is comfortable to hold and maneuver during intense battles or prolonged play sessions. ...The blaster's robust build quality also makes it suitable for indoor and outdoor use, offering a wide...

Liked the recon reinforcements, so decided to adapt it for another wobbly stock. This stock probably won't work for any blasters with the extra bit at the back after installing the reinforcements. ... Hardware needed: 4mm×25mm screw & hexagon nut

<p>Liked the recon reinforcements, so decided to adapt it for another wobbly stock.</p> <p>This stock probably won't work for any blasters with the extra bit at the back after installing the reinforcements.</p> <p>Hardware needed: 4mm×25mm screw...

Made a shortdart pusher because there wasn't one on thingiverse before... so yeah... have fun. You will need to switch the screwpost the return spring is currently attached to, so you can use that screw to secure the spring to the pusher. ...(See...

Be shure that the Gear of the Motor fits to the Pusher. ...I had to glue it at an ange.Works fine now.