nerf claymore mine 3d models

For better results, I print mine with four perimeter shells, making the twisted pin parts solid. Before inserting the finger pads into the bearing, I apply a small amount of SuperLube Synthetic Grease to each BB. American pennies have the same...

How mine differs: With my design, the switches are run in series to avoid a failure situation. If the switches were improperly seated or there was a failure in the wire, the RoBo3d would just raise up during its normal z operation and not throw the...

Mine is a standard one I got from Amazon and it looks like this:The length of the thread is not critical, as you can place washers or similar underneath.Also you will need 3pcs 608 ball bearings for the planet gears.Design and Source CodeThe...

In addition, a thin washer if the connection becomes too loose over time.----------------------------------------------------------------This is another spool holder for the Creality Ender 3 (Pro) - and my first "creation".I created it to be...

I tightened mine just enough so that the front panel stays up on its own when fully open. FRONT PANEL COMPONENTS I have included the following front panel configurations: lrs-350_foldingCover_front_dualSwitch.stl this is the dual switch...

This will vary according to how tuned in the printer is so I can't guarantee that yours will stay on like mine. It is far easier to just slide the kazoo into this basic one and it can be done one handed pretty easily. this is the biggest benefit over...

It may be enough in itself, especially in a toddler-free environment, which mine isn't. To make the attachment permanent, I melt together the two sides of the clip and the bottle. That in turn introduces small pieces of aluminium foil, but it is the...

Mine is PLA, and so far I've only experienced very minor warping that doesn't affect functionality at all. This could probably be improved by printing in ABS* (let me know if you try this). Note that this is only designed to work with the new 2014...

.The “Repair” contest seemed like a good reason to try my hand at replacing the driver's seat recline lever, because I'd been babying mine along for a while, and the the amount of my time needed to get to a store that might carry them (or find them,...

Open rocket says it needs weight in the nose (I printed mine hollow), so I added weight.Use a standard Pringles can cut down to 200mm in length for the body for scale (They're about 224mm normally with the ends cut off).I've included pieces for a...

I smoothed mine with sandpaper. The maze could be printed in PLA, but I would still recommend printing the lock in PETG.  PETG is more flexible, and the lock needs that flexibility to work properly.Above is a drawing of the lock. It goes in the...

Mine was at 600mm (~24") and it worked nicely 4 sheets of 3mm plexiglass. You'll have to measure your own dimensions but I recommend making the sheet for the door ~70mm taller and ~50mm wider than the others, but use your discretion Door Print 2...

to use other objects of Thingiverse than mine: print "Prusa i3 mount for MK8 extruder and an E3D hotend" by StevenQ-NE-UK (https://www.thingiverse.com/thing:1812853) + "Prusa I3 extruder carriage for MK 8 extruder" by ritaxiang...

 Then relax your hands on the saw so that the jig guides its travel and just push/pull until you're down to depth.Once you've cut the tails and transferred the marks onto your pin board, you can use the other two sides of the jig to ensure you...

mine was doing great until i revisted it to try to shorten the key so an i sanded the top of the plastic piece flat an for some reason now it has to be held side ways at the ignition to get it to start everytime, with it in the case with the key its...

 I like mine organized and well protected so just dumping a bunch of loose ammo or storing it outside of cans is a non-starter for me.So, to that end, I wanted to maximize the number of shells I could stand up in a Cabela's Dry-Storage Ammo Box...

For example, it could take the drill to a rich mineral deposit for drilling/mining. Mars human - A human inhabitant for your base, the human has a suit on that protects him/her from the elements and hides his/her hands. Printer...

To make the carriage, you will need: a SG90 Servo A printed ServoLocker (mine was printed in SLA for maximum precision) a short piece of 2.85MM filament, I used PETG as it is what I had laying around two springs a printed servo holder a printed...

mine are sleeved with Ultra Pro Matte sleeves. I tried to create this so there would be as little wiggle room as possible. After all, this isn't the thickest box. However, the player pad by it's nature (since it's consumable) means that there is a...

Mine didn't have as much working radius as I hoped for. Shop around and find better ones, I guess. It's designed around a Runcam Owl Plus. Not sure what all it'll fit. Throw a comment out with a link to a mechanical drawing of your micro cam and I...

Here's what you'll need to build this fume extractor: * 2 x 60mm fans (mine are 15mm thick) + You can use either of these links - if you want ones that are only 10mm thick, it would make it easier to get the carbon filters in place, but that's not...

Getting kids interested in science is a passion of mine and I have found 3D printing one of the best ways to do so. Can't wait to share this set with others. Thanks for reading! Instructions...

You can build it to your specific needs (right now, I'm using mine to run my 3D printer, which I keep in my workshop rather than my office). Because it's modular, you can swap parts out as needed. When a Chromebook breaks, you're basically stuck...

I've been using mine on a daily basis for years now and I haven't had any problems yet. Pictured parts are printed in Das Filament PLA at 210°C/50°C on the Creality CR-10. Post-Printing Just swap the acrylic stock part with the freshly printed cover...

For a 5 card wallet, 18mm length screws are perfect; I used McMaster 92095A472 for mine.One back panel. At time of publishing this I only have one style available, but I plan for at least a couple more that I'll try to add over the coming weeks when...

These bolts are sometimes called "hex head set-screws" because they are threaded along their entire length.I printed mine in black PETG from Plasty Mladeč.I've included both a .3mf file (PrusaSlicer - everything already set up ready for printing) and...

These cards fit in a regular sized envelope.Cut the postcard out of (colored) drawing paper (mine has a weight of 240gr/m2)Fold the card, if desired Glue the printed wire on the card using Super Glue:Put a bit of super glue on a piece of...

When I did mine, I actually cut one tooth off of the split belt and reassembled it in the plastic unit. Belt tension was always a little slack, even with tension fully adjusted, so this gave proper adjustment back. Put the metal carriage hanger...

Let me first give credit to the designs that inspired mine. I drew this one from scratch but I originally liked the idea from TerraVestra's design (https://www.thingiverse.com/thing:4548187) as well as CyberwareDK's remix...

I Set Mine to About 1.2mm - 1.4mm Above the Bed. There Are Some Duct Leveling Helpers Included with One of the Remixes Here: Https://www.thingiverse.com/thing:3481256 Update May 31st: Added 4020 Single Fan Cooling Duct. Update April 13th: Setting...