needle nose vise grips harbor freight 3d models

it's a wrench to get a really good high-torque grip on the adjustment knob of the green harbor freight suction cup workbench vise. step file included. ... [OnShape...

it's a wrench to get a really good high-torque grip on the adjustment knob of the green harbor freight suction cup workbench vise. ...step file included.OnShape link

I wanted a vise to hold my Harbor Freight rotary tool and stumbled upon the Dremel Vise. I modified this by making the bracket and base opening a bit wider and longer so the tool will sit better. I am sure more work can be done to improve this.

This holder was designed to hold Harbor Freight/Central-Forge part number P4614, 12 piece needle files with poly handles.

The needle files from Harbor Freight come in a flimsy plastic case, and the tip ended up breaking off one of my files in it. ...I designed this case to better protect and store the files.</p><p>There are holes for up to 6 3x8mm magnets to act as a...

These are a softer version of the very sharp metal jaws that come in the Harbor Freight 3" bench vise. ...They are easy to swap out when you need a softer clamping surface and can easily be sacrificial if need be, just print another set.

4" Soft jaws to fit a Harbor Freight vise.

... Here is my design to solve that problem. I've attached the .sldpart so that it can be edited to accommodate more files. I made it so that it is tight to put the files in because I figure you have a needle file set to make them bigger if needed ;)

then got home and realized my [needle file set](https://www.harborfreight.com/12-piece-precision-needle-file-set-4614.html) was similar, but there are 12 files, not just 10. So, opened up the design and adjusted for the set of 12. Same design as the...

then got home and realized my needle file set was similar, but there are 12 files, not just 10. So, opened up the design and adjusted for the set of 12. Same design as the other, can be printed as just the holder or as a "lazy susan" design using...

then got home and realized my needle file set was similar, but there are 12 files, not just 10. So, opened up the design and adjusted for the set of 12. Same design as the other, can be printed as just the holder or as a "lazy susan" design using...

print with tpu /and suitable infill. ...I liked dsmfool's version but have the 4" vise so used fusion 360 to modify it to fit the 4" version. ...printed in yoyi tpu .2mm layer height and 60% rectilinear infill at a 45 degree angle

Tray to hold Harbor Freight SKU 67888, (67885): 3/8 In. Drive Metric (SAE) Long Reach Ball Head Hex Socket Set, 7 Pc. Has embedded magnets (20x5x2mm) to help secure the sockets.</p> <h3>Print instructions</h3><ol> <li>Start printing the files</li>...

Compact carry case for Harbor Freight 12-piece Needle File Set. The Holes may be tight right after printing. Fortunately you have a needle file set to file out the holes a little. ...Pick the file with the largest handle (lets be honest the...

Customized version of https://www.thingiverse.com/thing:3265679 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3265679

A simplistic Rasp Holder that prints in place. ...Quick print. Used for the set of 12 rasps sold at harbor freight. Does not need Support! ...Print at .1-.2 mm layer heights for best results.

These are Harbor Freight 2 & 1/2 inch vise covers. They should fit any 2 & 1/2 inch vise. The exact size it fits is 2.55 inches or 65 millimeters. ...They should fit snugly to keep them from falling off.

replacement jaws for the Harbor Freight Central Forge table swivel vice to hold locks for lockpicking. I'm sure it could have other purposes, but this is what I made it for. ... So far I printed in PLA but am also trying one printed in Ninjaflex.

I made these jaws to fit this table vise: https://www.harborfreight.com/2-1-2-half-inch-table-swivel-vise-97160.html It has the same holding provisions (apparently for rounds, hexes, and squares) as the original. The original screws can be used to...

I have a set of these on a larger vise and wanted one for the new 3" vise. I prefer the long version, but included a short version as well. ...In the end I printed the short version because I didn't want to wait on the long version.

Customized version of https://www.thingiverse.com/thing:537516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=537516

this is a slight modification to the 4" soft jaws to shorten it up to just cover the steel jaw- my intention is to print this one in pla

Customized version of https://www.thingiverse.com/thing:1516335 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1516335

Ahegao handle for harbor freight workbench drawer.

Harbor Freight service cart with tools organization boxes

This is an insert for the Harbor Freight Bandsaw

A box and lid to securely hold set of Harbor Freight Probes. ... There is a remix that is a box for mini files from Harbor Freight as well.

I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.

I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.

A stand for a Harbor Freight Multimeter. ... I added some pockets for magnets to the stand.