nebulon b frigate 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

... clean it up.  Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).

Which means planning so the bridges will look nice enough/not stand out too much.This also means some very precise modeling so that the slicer can handle a bridged over area with a hole in the middle. Here, I build up to it layer by layer with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 40 use_mouse_ears = 0 custom_back_camera_x_size = 20...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos...

Using the paint supports tool in PrusaSlicer, put supports around the square cutout that you can see by looking through the bottom of the model. Look at the image below for reference.</p><figure class="image image-style-align-center image_resized"...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

Already renowned for their authentic sound, Casio's latest model takes it to the next level with its impossibly small footprint. Measuring 43 percent smaller than previous generation Privia instruments, the PX S1000 is literally half the size of...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

Check out the rest of furniture models from it, as they will fit nicely with this mini set! Bar pieces have special connections that allow you to attach them to each other in an unlimited amount of ways, and create any shape of bar that you desire,...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

... The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports.

So it was time to change the software for a version with customizable options. version 0.1 detail Version 0.2 is a rebuild of the FreeCAD model in OpenSCAD. While working on it some additional settings beside the number of legs made sense. Now there...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Also download the original 'COMPLETE.BLEND' from Jumpman971's Thingiverse so you can see the model in Blender. (Also get Blender.) (I'm pushing this out before a throat piece is remodeled because I have a 2-week vacation coming up and I'm busy this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

See the link below for a model that looks like the one I have. If I didn't have the laser boresighter, I would have chosen a cheap laser pointer in the $5 range or a cheaper boresighter in the $15 range. Perhaps I would have simply purchased a...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...