naruto 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 23...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Got home from work, so now it's time to work: My initial model idea looks nothing like what I later end up with. Its bulky and more suited for clipping onto a credit card. The idea was there but not the form. I just kinda thought of the idea and...

Each time I found that the support material came away beautifully… right up until I printed the final model. A tiny piece of the design broke off with the support (see pictures). Thankfully It's not an essential part. It's only there to keep the...

I have printed the model in 2 colors with an extruder, changing the color of the filament in Z: 150, except in parts 1,2 and 3 that have part of the roof and I have changed it in Z: 150.02. The dial I have changed the color of the numbers. I bought...

The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20 This box will fit in the enclosures made by Stepcraft. Hardware: DS 15 connector female (signal out) DS 15 connector male (signal in) Mono...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

 I've included 3mf project files from PrusaSlicer so you can see how I ran this model on my printers. UPDATE 27/01/2022: Created a rudimentary mount to hang the chassis under a shelf or table.  I decided to make a second unit to move...

remixed from the great work from https://www.thingiverse.com/thing:1681442 see it move https://youtu.be/rTlbqrB86YA -- big wheel: one side glued to the axle, other side tightened with screw (drilled a 1.8mm hole and use a 2mm screw); gear on the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I have the model assembled if anyone is interested; just can't upload a .step file (check the comments for it now). Keep in mind that you may need a shim (flat washer) to fix any misalignment issues with the Creality Heatsink. I've used this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

I've designed some custom shelves for my Warhammer 40K model painting supplies, including paints from various manufacturers. The system allows you to mount two shelves on either side of a wall and connect them with chains. For instance, you can...

Then it becomes matter of swapping the 5 tubes that lead to the MMU2S, but not to refeed the buffers each time.The model consists of two parts: a connector which is screwed between the upper and lower part of the body, and a bracket that holds two...

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

My daughter loves playing chess, but the magnificent pieces by NTX9 often fall out the original box when she tries to relocate.Therefor I made a remix that allows for a lid to slide in front of the pieces. The lid is of course based on the pieces...

See Latest Updates Below ----------------------------------- * The latest model now appears at the top due to rearranged pictures. I wanted a unique look for my 4x Santa figure, if that's feasible... Took various elements from multiple 4x...

I only own the flat styled one, so that's the one I used to model the part in SW. I think they are both called QuickClick. I believe I may have the older version, &amp; that they've been replaced by the round style (see further down).</p> <p>I can't...

Front TV (One piece) - This is the black and purple piece as one model, like in the OG version. You can paint it yourself, or leave it purple.</li> <li><b>Front TV (One piece, no supports)</b> - Same as previous, minus the grill lip</li> </ul> ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

**My Tinkercad-works:** [Coverplates + Hinges + Z&Y-FrameChainmount + Connectos-Hub + cutout-stamp](https://www.tinkercad.com/things/60ksBr4wvsb-s8-pro-coverplate-hinge/) [Hotend Mount + Y-Axis Chain...