nanopi neo 3 3d models

... for the heater cable). I also reinforced some areas a little and enlarged the mount holes at the front to better accommodate the coarse fan mounting screws. Fully compatible with the CR Touch that comes with the stock Neo (and Neo v2). ...

All credit goes to the original creators - I simply added a couple features and modified them to fit my printer. This was designed for and tested on my Ender 3 V2 Neo with a Spider 3.0 Pro hot end. UPDATE: I started having issues with getting a good...

There's also a small slit on the bottom of the case, I put that there to hopefully fit an SPI cable for the TFT35 SPI, I will use this case for that, https://www.thingiverse.com/thing:6478665USB Cable - This is what I will use to connect the PI to...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

This bracket mounts the factory spool holder from the Max Neo to the top rail. You can use the same screw that comes with the original holder. This is a quick prototype that still needs a little work, but I could not find anything similar. ... I...

This is a low profile gearbox designed by Team 1701. ...This gearbox has a pneumatic shifter that switches between a 5.13:1 gear ratio and a 7.43:1 ratio. This modular design can utilize Cims, Mini Cims, and Neos.

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

Complete replacement to the Ender 3 Max Neo tool drawer to hold a Raspberry Pi 3, Buck Converter and Relay. Design of the tool drawer should work for Ender 3 v2 as well. The design is intended to use the original "case" for the tool drawer but...

This is how I upgraded my Ender 3 V2 Neo to print high temperatures. All dimensions remain the same. Disclaimer: * Do at your own risk. This increases the risk of a thermal runaway and printer damage. * Forget the warranty. * I am still...

Remixed from: https://www.printables.com/cs/model/115518-biqu-h2-ender-3-v2-mounting-plate-with-bltouch Intended to be used with: https://www.printables.com/model/114869-biqu-h2-extruder-part-cooling-duct-mount and...

This holder fits the V2 Neo which comes with a stubbier small wrench (10.5mm handle), which will now fit. This holder should work really on any Ender machine and non other brands that have the same/similar rail. ... Note: For best finish print like in...

Can use MiniCIM, CIM, or NEO. Geared for 8" pneumatic wheel (12:48 16:50). Second stage gears should be steel, just like the KoP ToughBox Mini. Easy to adjust speed with 10 and 11 tooth pinions on 12 tooth spacing from Vex Pro. ...Designed in the...

Additional parts needed 2@ M4 X 16 screws 2 @ M4 T Slot Nut Fastener This is a top gantry LED mount for an END 3 Max Neo. It pairs with my X Axis gantry LED mount. https://www.thingiverse.com/thing:5931926. This design is good to give overall...

Original posting: This is a remix of combination of Vap3Lif3_MCMXCV fan duct that was designed using https://www.printables.com/model/378928-anycubic-kobra-neo-fan-duct by Martin. The circular fan duct was found on the internet (no idea where I got...

This is a direct replacement hotend cover for the Ender V2 Neo. It works with the standard fans only. It lines up with the blower fan intake better than the original. I added 4 LED's to the eyes and below to light up the print area. I use 2k ohm...

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

This is a mod for the Pico Neo 3 Link VR headset. With this mod you can use the headset without the face gasket, like with the Quest Pro. It looks very simple, but has all the features I wanted to have, without being bulky. -It will rest on...

This is a halo type face gasket for the Pico 3 Neo Link (P3NL). I took the idea from the Pico 4 GeekVR halo, which hasn't been produced for the P3NL. It gets your eyes as close to the lenses as is practical, which improves the field of view.The...

Ender 3 cover

tool holder for the tools supplied with the ender 3 + a cutome case

Remixed from https://www.printables.com/model/270817-ender-3-v2-extruder-cable-guide Supports needed. ... It's very tight

Ender 3 v2 led top and side led bar The installation was made with a 1 meter led 5050 strip

My cover break apart after many times disassembly so I remix this replacement part. ... Original design: https://www.printables.com/model/377901-ender-3-s1-x-motor-cover Print like image to save time & have better tolerance.

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

... ...I used original reel mount hardware to attach it to overhead gantry. I screwed the two pieces together for horizontal stability. the screw hole is 3.5mm. ...You can position the assembly wherever you like on the gantry to suit your needs.

A sleek and modern 3 Corner Table model has been carefully crafted in this open-source powerhouse of a program. Key highlights include: -5 Unique formats are provided, offering maximum flexibility for various projects: Blender (the default...