nanoleaf alternative 3d models

They are basically a copy of the Nanoleaf. ...I used the top part only as a template and cut my own opaque acrylic, this gives a really nice look. Parts:2x 500mmx400mm Milk opaque acrylic 2 mm thickWS2812BECO White PCB, 5m 60 IP30NodeMCUWLEDPower Supply...

Nanoleaf fake xD

easy to mount can be hung with thumbtacks or screwsthe "Nanoleaf_cache" must be glued to last wellanother version more modular and in progress

Could use command strips or a hook/screw Printed using black & white ASA, supports are not rerquiredI really liked this NanoLeaf design but could not for the life of me get the clips to work, watching the video it looked super simple. I printed out 2...

I made this nanoleaf cover more resistent.

I made this nanoleaf cover more resistent.

puoi vedere l'effetto finale sul mio canale youtube https://www.youtube.com/c/Emieasilyhomemade https://youtu.be/xG8IhXT730M

puoi vedere l'effetto finale sul mio canale youtube https://www.youtube.com/c/Emieasilyhomemade https://youtu.be/xG8IhXT730M

Made on Autodesk Fusion 360 as a base for a Nanoleaf Lamp

I wasn't impressed by the official Nanoleaf wall mounts, so I created my own versions that didn't need any cutting and offered sturdy edge support.

nanoleaf 139*120*32mm in size suitable for scaling There are magnets and cable channels. ...It consists of two parts, the cover and the body.

1-2cm langen Kabeln in Segmente zusammen lötenAn beide Enden des Segments ein längeses Kabel an die Datenleitung löten (dieses müssen später von Panel zu Panel reichen)An ein Ende des Segments auch noch längere Kabel an die Pads für die...

I created a nanoleaf replica that measures approximately 20x20 centimeters. This project is still evolving, with ongoing development of the code and electronics. ...My current prototype serves as a near-final version, awaiting further refinement.

... and printed out a few copies. The "Basis" attaches directly to the wall, while the Nanoleaf Panels wrap around it, and the "Scheibe" sits on top; all you need to do is drive a (4mm) screw or nail through the pre-drilled holes for a secure fit.

Just my attempt at a WLED driven Nanoleaf. Each panels corners gets three WS2812B LEDs from the 60 led/m strip. Each side holds two magnets. Be careful to orient those correctly when inserting them or the panels will repel each other instead of...

Nanoleaf hexagon for std RGB strips. ... - Print panels - Glue them together - install controller/Converter - install LED-Strips - Glue top/lids - Enjoy Misc: - 3M of LED RGB kit 1 x Main 2 x Body1 1 x Body2 2 x Body3 -...

Mine did but I fixed it in the right angle with tape :DFeel free to ask if you need any help or have questions. Things that you need for the build:LED Strip: (Govee RGBIC LED Strip 5m)4x M4x10-15mm screws1-2 kilos of White PLA Filament for 12...

I designed this DIY project to bring a bit of brightness into my office without breaking the bank on an actual NanoLeaf setup. I had no intention of shelling out hundreds of dollars for the real thing. ... This project is outlined in the video below: ...

I wasn't a fan of the official Nanoleaf wall mounts' design, so I created my own versions that didn't need cutting and provided extra support along the edges. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution:...

Here is my Nanoleaf remix from surrbradl08 https://www.thingiverse.com/thing:3354082 some improvements: - ws2815 optimized (4 Pins) - you dont need a 4mm gap between the triangles - the lid (cover) is only on the top - easy lid remove - less material...

Nanoleaf hexagon for std RGB strips.Print panelsGlue them togetherinstall controller/Converterinstall LED-StripsGlue top/lidsEnjoyMisc:3m of LED RGB kit1 x Main2 x Body11 x Body22 x Body3Print SettingsRafts: NoSupports: Doesn't MatterResolution: 0,2...

I always wanted a Nanoleaf but they´re so expensive so I thought I can print one. So here it is. I used WS2811 LED Stripes and a ESP8266 with WLED to light this Model up. These are the stuff I used: WS2811...

Bonjour à tous voici ma conception pour vous permettre la création de panneau ressemblant a des Nanoleaf pour un coup beaucoup moins élevé.Vous trouverez le fichier F360 et en .step pour pouvoir enlever ci vous le souhaitez le marquage sur le boitier...

Nanoleaf

- Added Strobe Pattern - Added Sound Reactive support - Some code cleanup and new parameters for configuration - New step-by-step installation instructions...

Beginning work on nanoleaf shapes connector

Work In Progress // Nanoleaf Version 2 - Smaller Radius

Panel and Wall Support for 3DFactoryAlex's Nanoleaf Version

Walls and base with snap joins for nanoleaf lights.

This is specifically designed for standard Nanoleaf frames.