na miata gauge cluster 3d models

Miata Boot Light Switch Fitting

This shim fits into the holes in the dash of the Miata NA/NB usually occupied by the cruise control, dimmer, defroster, and mirror switches. ...It's currently spec'd to accept [this...

Was inspired by Flyin' Miata's RAM vent mount (https://flyinmiata.com/products/na-nb-vent-ram-mount?variant=43356734390527) so I decided to create my own for this phone mount...

Using the bracket designed by DigitalSolo as a base, I snipped off the original mounting points and added some to fit in my Miata's engine bay (NA, LHD). This mounts on the side of the fuse box in the engine bay in place of the wiper fluid reservoir....

Some NA Miatas came from the dealer with tweeters drilled into the top rail of the door panel. The covers suck and so I made these that clip into their place. ...They should all be the same, but I included the raw file incase you need to modify it.

This is the part that connects the selector lever to the cable that actuates the blend door in NA Miata's. Mine broke I could not find just the plastic piece and a replacement for the whole assembly was too expensive. This works well as a replacement...

naca duct intake for Na Mazda Miata I printed this on abs 10 infill .2 resolution with the bed at 110 and nozzle at 240 fits perfect you do need to measure very well where to cut otherwise, it will hit the headlight structure

This is for my NA miata but will probably work on other models. When I installed new speakers in my miata the speaker cover panel clips broke upon removal. I made this design to clip the cover panel back to the door. It's not perfect because it's...

To remove the ashtray from your 1st gen Na mazda miata, follow these steps: 1. Open the glove box to access the screws holding it in place. 2. Remove two 8mm bolts that hold the ashtray cover in position. 3. Gently pull the cover away from the dash...

These are used to replace the front running lights on a NA Miata. Comprised of a backplate, a light to backplane adapter you epoxy onto the backplate, the front housing, and a diffuser plate. I recommend PETG for all components and LED lights only...

Here is a bracket I designed and printed to hold a oil catch can for my NA Miata. Instead of bending aluminum flat stock, I used the dimensions of the windshield washer reservoir to create this bracket. Keep in mind that this bracket mounts where the...

Remix of [this cup holder](https://www.thingiverse.com/thing:1667376) and this Miata phone holder from GrabCad: https://grabcad.com/library/na-mazda-miata-cup-holder-cell-phone-mod-1 I don't have the OEM ashtray that the GrabCad phone holder was made...

This design is specifically tailored for my NA Miata, although it's likely adaptable for other models. When installing new speakers in my Miata, the speaker cover panel clips snapped upon removal. To resolve this issue, I created a clip to securely...

On my 1997 NA Miata there was a hole on the drivers side firewall next to the speedometer cable that had a plug in it. I needed to run some wires from the engine bay into the car and so I designed this to fill the slot. The hole is 8mm and I'm happy...

This is the Air condition knob for NA miata's (1990 to 1996) with AC option. The knob will fit exactly the same for non-ac version. Functions as it should, can't comment about robustness just yet. I printed this at 0.2mm resolution and the fit was...

Installer for Rear Main Seal on 1990-2005 (NA/NB) Miata. Using this tool requires minimal effort, align the rear main seal with precision and install the flywheel bolts, then slowly torque them down to secure the seal in place. Be cautious! This...

This is a plug to fill the 2 side holes found in some Mazda MX5/Miata NA centre consoles. I don't use this area with the cup hold or ash tray inserts. Blocking these holes just ensured that nothing will fall into the hole. They are designed...

This is the Air condition knob for NA miata's (1990 to 1996) with AC option. The knob will fit exactly the same for non-ac version. Functions as it should, can't comment about robustness just yet. I printed this at 0.2mm resolution and the fit...

This part is a direct replacement for the (discontinued) Mazda Miata headrest speaker box.

Mazda Miata Brake Light Modification. ... Check out this awesome modification on Facebook at https://www.facebook.com/groups/1090060834506043/.

This is an adapter specifically designed for holding an 8oz Red Bull can in place within an NA Miata cup holder. It's crucial not to print this adapter using PLA, as it will shrink significantly over time when exposed to the heat of a car. ABS or...

A larger cupholder designed specifically for the Mazda MX5 NA Miata's cupholder support, originally created by 5str3l0k and available here: https://www.thingiverse.com/thing:2501911. The ID hole is 3 inches in diameter, but I'm still working on this...

It should work with the retro switch from some Miata vendors, but no promises are made. I fabricated my own aluminum plate and switch guards using components sourced from eBay. ...Perhaps this will be helpful to others in the future.

This is a telescopic A/C vent for NA or NB Mazda Miatas designed to replace the eyeball in the stock A/C vents. All parts were carefully modelled in Solidworks. Fed up with having vents that couldn't be closed when not in use, I decided to create new...

When i bought my Miata it was missing the pipe for the HVAC, so i decided to print adapters so i could use standard 102mm HVAC hose and hoseclamps. ...I used the standard plastic fasteners to attach it to the car.

Does your Miata's hood rattle excessively at idle speeds? ...Solve the problem instantly by printing out two of these custom-designed inserts, carefully sanding them down to precision size, and then securely attaching them to your hood's bushings for a...

A custom trim piece designed specifically for 1990-1997 Mazda Miatas, this unique cover is crafted to fill in the gap where the center console has been removed, leaving a smooth and finished appearance in its wake. ...With precise attention to detail,...

Have you noticed an annoying 'click' sound when pressing in the clutch or cruise control not working on your 89-97 Miata? The culprit may be the infamous 'Blue Thingy'. Modeled after the OEM part G030-43-029 which is similar to B001-43-029. ... ...

This replacement part for the Mazda Miata Softtop Latch is crafted to perfectly replicate the original design. It features a durable structure that matches the exact specifications of the NA01-R1-311 number. ...To ensure its strength and longevity, it's...

To streamline the design, I removed the Miata script and centered both the phone and cup holder cutouts. The plate's shape has been adjusted to better complement the console section, featuring a rounded top and a square base. ...Additionally, the...