myminifactory elegoo mars pro 3d models

Pieces joined together and inexpertly trimmed using OpenSCAD

This is a basic tray made to store a resin vat. The tray raises the vat up so that it does not rest on the FEP screen, therefore helping to avoid accidental FEP damage. Fairly simple print and design. ... I'm working on a 'hotel' that will hold...

Pieces joined together and inexpertly trimmed using OpenSCAD

I got the Sovol3D flex-plate and apparently it needs a 2.5mm spacer. I printed the spacer but unfortunately the stock screws are too short for it to work. So I designed a replacement z-stop and added the 2.5mm to the end. ...Works like a charm.

This is a VAT cover with cutout for the mounting on the printer. Very convenient to use. ...Can be 3D printed and used.

this is for setting your tank down on a table or desk without damaging the fep film. ...very simple 2 step design, printed with 2 outer lines and 10 percent infil print with a brim as it is quite thin on the edges

Original part: https://www.thingiverse.com/thing:4546094 which was then remixed / changed: https://www.thingiverse.com/thing:4563449 and later remixed once again by me. This remix removes some material from the bottom, making it easier to print...

Just a basic sturdy tank Cover for the Elegoo Mars 2 Pro. Just for when the tank is in the machine. This is to stop foreign bodies entering and reduce light exposure when not in use. Put a tail of a few inches of electrical tape around the...

Spacer Z Limit for Elegoo Mars 4 DLP compatible with 2.6mm flex plates. Spacer fits snug, but is still removable, if required. Tested with Wham Bam Flexible Build System on Elegoo Mars 4 DLP. Do NOT use transparent or translucent resin for print of...

Check out this game-changing tutorial on how to create a precise bounding box for your Elegoo Mars 3D printer using the powerful software Chitubox. Get ready to take your printing experience to the next level with expert guidance and step-by-step...

These drip trays were designed to work seamlessly with the Elegoo Mars 3D printer, ensuring optimal performance and reliability in even the most demanding applications. ...Printed using high-quality PLA filament, these drip trays are perfectly suited...

can be printed by my Elegoo Mars 2 for Elegoo Mars/Mars2/Mars2 Pro The first two attempts were rather poor. Since I was running out of gray resin, I asked myself what would happen if I just pour black. That's the result. A "colorful" tub, for...

Here is a lid with handle for the resintank from the Elegoo Mars 3. Simply diagonally on and off without having to loosen the screws. ... The handle can be pressed in and fixed with a drop of glue.

This is a custom foot I engineered to snap onto the stock feet that are pre-installed on my Elegoo Mars. ...Constructed from durable TPU, these feet enhance stability and prevent the printer from slipping on my workspace.

This is a Z-axis bearing support designed specifically for the stepper rod used in Elegoo Mars 3D printers. ...It's a versatile component that works seamlessly with both Generation 1 and Generation 2 models of these popular machines.

This is a simple Vat Cover i designed for the Elegoo Mars 4 Ultra.There is a small handle to print which i glued on top of it.It is working quite fine. I hope it helps you guys :)It fits the Mars 4 9k too! ...(thanks to nemlu)

Vertical bolt/nut lightly loose to allow swivel https://www.thingiverse.com/thing:4118839 Related designs: Elegoo Mars VAT drainer System https://www.thingiverse.com/thing:4819340 Elegoo Mars USB support https://www.thingiverse.com/thing:4816644...

Resin vat slide cover for Elegoo Mars to protect vat on and off printer. Designed to slide under screw mounts or placed on top when vat is removed. Other designs either cut around mounts leaving some areas exposed or only work off the printer. Can...

This is a handle for the UV cover of the Elegoo Mars. The shape fits perfectly into the recess on the cover where the QC Pass sticker is located. I secured this in place using 3M VHB tape, but there's also a hole at the bottom for a 4mm screw if...

Poignée pour la Elegoo Mars 5 Ultra et TOUT autre machine a capot. Elle se colle facilement avec un double face comme celui ci : https://amzn.to/3RF6rcqpeu être placer n'importe où mais ici en face avant aucun soucis pour la soulever a une main...

This is a spacer to raise the lid of the Elegoo Mars 3 by about 15mm, and provides a slot in the rear to allow a cable to be run inside the enclosure, but still allow the lid to be fully seated. ... The red item around the printer's vertical column is...

This is a cover for the resin vat of an Elegoo Mars 4 DLP printer.The cover clips into place. ...  You may need to file the clips down depending on your calibration and preference.I made this to reduce fumes while the printer was idle, as well as to...

This is a remix of this https://www.thingiverse.com/thing:4765828 I modified the support tip to fit the Elegoo Mars 2 head plate. I made a second model with more angle to allow taller models to drain with the cover on. ...

I'm not a fan of the standard wheel design either, so I came up with my own version. ...To set up your Elegoo Mars, head over to the original configuration guide on Thingiverse at https://www.thingiverse.com/thing:3773723.

The Elegoo Mars receives a boost with its anti-odor filter upgrade. Simply swap out the lower ventilation grille for this innovative addition, all without making any permanent changes to your printer's internal design. ...For even greater effectiveness,...

A Remix of Phesketh01's Vat Cover, Born from Xantrix' Original Design, Sliced into Two for a Unique Kitty-Corner Display on the Elegoo Mars Printer.\r\n\r\nI Passed Up Printing It Myself as I Managed to Get an FDM Printer Before This Project Reached...

I built my own Elegoo Mars Z-Rod Bearing Holder and it's a slightly looser fit compared to some other designs out there. Unfortunately, this led to some issues with the Z-axis rod jamming in my setup. ...The bearing size I'm using is 8-22-7 (608).

This kit is suitable for mars，mars pro，mars C，mars2 and mars 2 pro machines video：https://youtu.be/m1AdmriOOnQ Detailed list: switch（KCD1 15*21mm Mini Black 4 Pin two position toggle switch）*1 DC Jack（5.5mm x 2.5mm）*1 DC power cable splitter one...

This is a simple solution to move the USB on a non-P/Pro Elegoo Mars to the front. By attaching this clamp externally, you can avoid making significant modifications to the printer itself. Internally, disconnecting the cable from the backing plate...

This is a simple lid to cover the resin vat for the Elegoo Mars 3. This was designed using the official mechanical drawings from Elegoo as a template, so fits pretty nicely on the vat.NOTE: This is not a snug airtight fit, as there is no gasket. I...