mx 5 nc 3d models

A quick 3D scan of a Mazda MX-5 subframe.

Spacer for shift knob and leather boot for MX-5 NC and Skunk 2 shift knob

The dome light switch in my Mazda MX-5 (NC) stopped working properly. The rocker switch would slide all the way from ON through DOOR to OFF, then back again. Additionally, the contacts behind it weren't making a secure connection, which prevented the...

I recently replaced the OEM antenna on my girlfriend's MX-5 NC after it started disintegrating, opting for a cheap alternative from eBay: https://www.ebay.com/itm/Universal-3-5CM-Car-Carbon-Fiber-Screw-Aluminum-Short-Stubby-Antenna/112790542748...

This is a Mazda Miata MX-5 NC (2005-2015) clutch and brake pedal stopper. The original stoppers tend to disintegrate with age - mine lasted about 10 years. Mazda does not list this as an individual part, making it almost impossible to find a...

Old OEM antenna on my GF MX-5 NC started disintegrating, so I bought cheap "antenna" from eBay to replace it: https://www.ebay.com/itm/Universal-3-5CM-Car-Carbon-Fiber-Screw-Aluminum-Short-Stubby-Antenna/112790542748 But I did't bother reading the...

Mount for GoPro to attach to wind deflector in NC MX-5 Attached with 4 M3 Screws

... Instructions Using the following settings: Wall thickness is set to 6mm. Bottom thickness is set to 4mm. Usable tool depth is set to 20mm. Number of faces is set to 15. Drive size is set to 0.5 inches. ...Filter diameter is set to 76mm.

Mazda Miata MX-5 NC facelift silhouette key Also check this design on t-shirts and other merch: https://www.redbubble.com/shop/ap/118083359?asc=u Follow me on Social Media for More 3D Design Adventures! ... 🎥 TikTok:...

Clamps securely around the standard MX-5 NC/MK3 towing eye, providing a sturdy base to attach an external action camera. I chose to use PLA due to its availability, but I wasn't confident in its strength so I opted for epoxy to bond a low-cost...

A lower resolution scan of a rear subframe.

A lower resolution scan of a rear subframe.

100% infill recommended, PETG, 250°C at least for good adhesion between the layers of the claws.

The ball fits BlitzWolf BW-MH1 phone holder. The ball is so far right caouse of whiper switch proximity. Print with materials capable to survive in hot car interior. PLA not recommended - it will require retightening from time to time - PLA slowly...

A simple bung to fill the holes left behind after removing the factory underseal.

Clutch alignment tool designed specifically for a 5-speed NC MX-5 model. Individuals with a 6-speed clutch in hand are encouraged to share their measurements, which will prompt an updated design incorporating those specifications. ... This tool...

Hi, I wanted a cheap and easy way to install a diferent intake on the Miata to increase intake noise (no performance gain expected of course, just fun). Also I wanted it easy to go back to facotry airbox. So I designed this to retain the factory MAF...

Humans craft partitions using sturdy 0.25-inch thick MDF boards. ...Custom plastic caps are expertly 3D printed to fit seamlessly into place.

I replicated the blank piece of trim on the boot of my NC that contains the keyless entry sensor in later models. I've included the blank piece so you can add your own camera mount to it. This mount clips right into place, just like the original...

This cable tidy will get rid of the annoyance of that dangling USB cable going to your phone. Simply loop back the cable on itself to give the right length, slip it into this and drop it into the small tray under the heater controls. ...No sticky...

I bought a pair of aftermarket side indicator repeaters for my MX-5 but was unhappy with the fit so designed a spacer to reduce improve the seating and look. I printed mine in PETG with shells and top/base values to make them nearly solid. ...

This is a clutch alignment tool for NC Mazda Miata with a 6 speed transmision. ...Should also work for many ford duratec engines as well.

1/2 socket adapter to rear brake piston of Mazda MX-5 NC  for me, it worked even printed in PLA, 4 perimiters, 30% infill

I have a 2012 Mazda MX-5 NC and I bought a Mishimoto carbon fiber shift knob which comes with a set of adapters to fit different cars. While it does have an adapter that works for my car, the adapter is really short and does not allow you to thread...

Designed this for a Mazda Miata MX-5 (NC) cubby hole on the driver left side. It fits really well but may want to double side tape it down so it doesn't pop out ever or come with your phone. Designed it to where you will drill a hole in the back of...

Neutrik XXCR Color Code Rings Designed for Easy Assembly with NC-MX Connectors Through Customizable 3D Printing. ...Scale Dimensions Accordingly Based on the Shrink Rate of Your Filaments to Ensure Perfect Fit.

Mazda Mx-5 Miata

mx-5 heel protection

Mazda MX-5 Miata, 2016, I ❤️ Mazda

This is a model of Mazda mx-5 nd,printable.