multiwii and megapirate aio flight controller 3d models

A blank for design fitting.

This is a compact rendition of my primary Reptile S800 Flight Controller and OLED display mount https://www.thingiverse.com/thing:2680791 (note the red print in one of the photos for comparison). I aimed to create something that could securely hold...

The new universal mount kit was primarily designed for the Pitlab AP system but also includes various options like dampened and un-dampened base plates for the iNav flight controller or other systems with 30.5 x 30.5mm mounting. There's even a plate...

... M3 threads into the bottom part of the enclosure. Finally, insert the Flip32+ flight controller into its designated position within the newly created space, followed by securing it using four M3x10 nylon screws to effectively seal the unit in place.

I've been trying out my new printer and mounting system, and so far, it's printing and securing perfectly. I've only conducted a few outdoor flight tests, but I'm optimistic that this setup will resolve the problems I've encountered while flying in...

A simple printable model which easily fits Controllers. ...The adapter gives better flying experience when using a controller for simulator.

It's just a couple of "cups" with a hole for an M3 screw and a yellow ear protection foam cut to desired length. They are glued together with epoxy so the screw won't turn and the foam stays in place. One of the cups has a raised boss on the screw...

... firmly in place and the foam stays snug within the cup. One of the cups features a raised boss on the screw side, ensuring that surface mounted components soldered near the mounting holes are safely secured, and it works flawlessly as intended.

In 2014, KK version 2.0 and the buzzer were made available for download in both SolidWorks (SW) and STereoLithography (STEP) formats.

... to achieve a compact FC stack. ...In particular, it's crucial for the new super slammed builds where space is limited. The spacers come in various sizes for M2 hardware and their corresponding heights are as follows: M2x4mm, M2x5mm, M2x6mm, and M2x7mm.

https://www.thingiverse.com/thing:4684636 make sure the hinge part and restraint part is perfectly centered and properly glued to the wall. Mut them all the way down to the bottom of the bay to have the FC perfectly level with the fuselage and have...

... the aircraft. If mounting on a flat surface, the glue should seep through the holes to add extra stability. If attaching to a rougher surface, fill the gaps between the mount and the aircraft with glue through the holes for a rock-solid attachment.

Here is the rewritten text: A compact human-sized cover measuring 20 by 20 millimeters comes out of my 3D printer with precision thanks to a high resolution of 1.5 millimeters, and I've found that infill density makes little difference in this case.

Strategically integrated into this base are recessed channels for wiring, as well as carefully designed slots granting effortless access to the USB and SD card slot. ...Furthermore, the lid itself was meticulously crafted using Tinkercad's intuitive...

Here are some basic setup steps for assembling your device: Print the top and base parts with a precision of .4mm using solid infill, keeping a minimum build volume size of 6x6 inches in each axis. ... Next step is cutting accurate 5-40 threads on the...

... mounting race quad FC. ...It fits perfectly, requiring only a drop of hot glue to secure. If you need to remove it, simply use acetone. I tested the design with INAV in angle mode and added a 10-degree increase on pitch to prevent altitude loss.

I am now searching for someone who can 3D print the prototype and its corresponding knobs. Best regards, Nick. ...Note: Due to a comment about side latches, I've created a new version of this case available here -...

The outer diameter of each washer is 4mm, while the top and bottom hold diameters are 5mm. You have three different options based on your FC thickness: 1.2mm, 1.4mm, or 2.0mm. ... Here are my print settings: Printer Brand: MakerBot Printer Model:...

Most, if not all, of the 4in1 6A and 10A ESCs on the market rely on M3 holes and hardware, but unfortunately, the standard hex standoffs are too large and often obstruct SMDs on the board. This spacer is designed to eliminate the need for M3...

This multiwii quadcopter features an aluminum frame with 3D printed mounts for enhanced stiffness and a high first eigenfrequency, which should help reduce the rolling shutter effect when using a CMOS camera. Check out the flight in action here:...

Tray for the flight controller and ESC to fit the volantex ranger 2000 and 1600.

This is an F4 flight controller branded by Hobbywing, and designed for racing or freestyle quadcopters.

The DJI F450 is now supported to use an OrangeRX receiver and a TMF Pro flight controller.

Mount your Quadcopter's Flight Controller using the provided 15mm Standoffs for sturdy support and stable operation.

... ...Its sleek design takes up minimal space while providing a high level of control over the aircraft's movements. By incorporating advanced sensors and algorithms, this controller enables precise navigation and stable flight in various conditions.

Package Contents: Mounting plate for drone/quadcopter applications Flight Controller Mounts (30x30): - Flight controller mount 30x30: Standard Plate Configuration - Flight controller mount 30x30_1-6: Plate with Spacer on One Side - Flight controller...

I created a custom version of the DALRC ESC and Flight control system specifically for designing quadcopters. Feel free to incorporate this into your designs as you see fit. If you choose to share your projects, don't forget to give me credit...

Pack of mounting plate 30x30 for drone / quadcopters Flight controller mount 30x30: Flight controller mount 30x30_1-6: Plate with spacer on one side Flight controller mount 30x30_2-6: Plate with spacer on both side Flight controller mount 30x30_3-6:...

Mount alternative flight controllers on Graupner Alpha 300Q frames.

Mount for Quadcopter's Flight Controller Featuring 10mm Spacers