multiwii and megapirate aio flight controller 3d models

This sleek enclosure is designed specifically for the Hobbyking KK2 flight board, boasting a screw-free design that allows for easy installation on almost any quadcopter. ...Strategically positioned mounting points enable secure attachment via straps or...

The plastic parts and dampers that come with that frame disappeared in the yard so I had to make this cradle to mount the controller. Should print out of the box, but will need some screws, small washers, and dampers. The sidewalls arent really...

Link to Video: https://www.reddit.com/r/virtualreality/comments/hox0mk/diy_vr_flight_stick_for_vr_thingiverse_download/ Printed out of ABS, and tied together using Elastic Paracord ordered from Amazon, Link Below:...

V1.0 features an added slot for the voltage cable and improved screw holes in the top casing. This no longer qualifies as a work-in-progress, so expect minimal updates. For those who prefer a tabless design, I've also included that option. Simply...

remixed Rob's excellent mount to snap on the front spar a little better and has holes for 30mm FC and holes for zip ties.

Tray is designed to work with MATEKF411WTE and gives it a nice location, currently in Mk1 and still in testing, it positions the Compass and GPS at the center of inertia (roughly). ... it uses M2X6.5 threaded inserts and M2 fasteners to attach around...

Simple remix, needed it a little stronger and thicker. ...With everything attached the arms on the original snapped right off.

You'll need two side pieces and one each of the bottom, middle, and top. V3 of the sides are if you want to use double sided tape or glue to secure it in the cockpit. I made the v4 with longer notches to make room for velcro if you want to go that...

The individual modified the hole size to 30.5mm x 30.5mm, resulting in a more precise fit, and also created hot glue receptacles at the base.

I designed a straightforward FC adapter, which I successfully printed in TPU material. ...It functions flawlessly on both my Stingy frame and an Airbot 20x20 setup.

Humans need a way to easily install their ESC and FC. ...We've got just the thing - this comprehensive kit has everything they'll need to get started.

This is a 30.5mm to 20mm FC adapter. ... The 20mm mounting uses 2mm screws and can be tapped as is. ... Fits my Xrotor nano stack perfectly!

A concept submitted by a viewer has sparked the potential for this design to undergo revisions based on user input and subsequent feedback.

Users have the option to include integrated spacers on both the top and/or bottom of the 30.5mm and/or 20mm holes, catering to their specific requirements. When standoffs are chosen for the lower part, the file will automatically be divided in two...

A low profile adaptor to fit 20x20 FCs onto 30x30 ESCs or frames. ...I split it in half and made it 2 pieces so it is easy to pass through wiring like ESC harnesses.

I've crafted this solution as a result of losing my standoffs and screws, prompting me to create something entirely new rather than purchasing additional parts. ...I encourage users to share their thoughts on areas for improvement.

Remixing the MKQV C1 FC Deck with its signature 30.5mm and 20mm hole spacing to seamlessly integrate with the original deck supports, now readily available from the iTSV C1 Chaser Parts line-up.

This is a 30.5mm to 20mm FC adapter. ...The 20mm mounting uses 2mm screws and can be tapped as is. Fits my Xrotor nano stack perfectly! ... Category: R/C Vehicles

... in reverse rotation mode. ...It will work effectively on any quad using an FC with 30.5mm mounting holes, provided ESC wires and XT60 do not obstruct it. ...Print this part with a 100% infill and have it stand upright as shown in the render.

... ...Two 6mm M2 nylon standoffs, one pair of 2x, are also required. The mount fits snugly under the spar, securing it in place with a small amount of glue if necessary. Printed with two shells and five percent infill at 101% scale using ABS material.

Setup Tasks: The Arduino Due boards show up with identical USB names and device IDs, which can cause problems if you're using more than one panel. I've seen DCS switch back and forth based on how the game loads up the panels. Dakor91's comment on...

... a difference in keeping your drone stable during rough landings. ...It helps absorb impact and prevent damage to the sensitive electronics inside. ...This is especially crucial when flying in windy conditions or trying out new tricks with your drone.

... FC Soft Mount for ultimate flexibility! ...You've got two powerful files at your fingertips - one tailored specifically for a 30.5x305 stack, and another for 20x20 stack precision.\r\n\r\nBring it to life with Ninjaflex printing technology.

Weight is critical when performance is key: This lightweight unit tips the scales at just 4.4g and can be securely fastened with four rugged M3x8 nylon screws. ...It measures a compact 39.2 x 8 x 39.2 mm, making it an ideal fit for any design requiring...

... ...Although it hasn't been printed or tested yet, I'm hoping it will meet expectations. For now, I've designated this model as a Work In Progress, and I plan to update its status once users have confirmed they're satisfied with its performance.

This project marked my second successful creation in OpenSCAD and my first fully customizable build available on Thingiverse. I'm confident that it can be optimized further, so please feel free to experiment with it and share your feedback on how...

Strategically placed cut-outs at the top enable effortless installation and tightening of battery straps. I've included the OpenSCAD design file for anyone interested in making modifications, but please note that multiple versions of these frames...

In version 2 of the KK2.0 Case, M3 screws now securely fasten the KK2.0 to both the upper and lower parts of the case. The overall thickness has increased from 1.5mm to 2mm, with each part receiving new dimensions or designs. The global measurements...

There are places for FC [25x25 mm], VTX [30.5x30.5 mm], GPS and quick-release connectors for wings. Under VTX, I installed a PC fan 40 * 40mm just with glue. Maybe someday I'll remake the model for him. ... My equipment: Matek F722 WPX Rush...

Here is the V2 of the KK2.0 Case : Now the fixation is made by M3 screws where the KK2.0 get fixed by the upper and lower part of the case. In English from French : "the KK2.0 is took in Sandwich" :-) The global thickness of the case was 1.5 mm, now...