multiplex rc gliders 3d models

My Multiplex switch case had been broken, so i draw and printed a new one.This is made out of ABS 70% infill.I lighlty filed/sanded the exterior face to have it smooth.Clean the holes with a drill bit  (1,5mm) and you're done.

Motor Mount for Multiplex RC Planes Like Mentor.

An FPV mount for a Multiplex Funjet is available at Tower Hobbies (http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXZWK8). It was skillfully designed in Google Sketchup by a friend and printed using an UP! Mini 3D printer, emphasizing the...

... to secure your models antenna and prevent cable harms through physical penetrations on the outside of the Fuselage. ...Especially for Carbon fuselages.If you are looking for a new high quality RC model glider visit CRG at www.composite-rc-gliders.com

High-performance Lego compatible remote-controlled gliders and complementary components, ideal gift options for enthusiasts of aerodynamic modeling.

I needed a replacement for a missing wing support on my Multiplex Lightning off-road car, which is actually a Thunder Tiger clone. To get it just right, I pulled out the User Manual and took careful measurements, making some small adjustments along...

This adaptor implements a folding EDF (27mm inner diameter) for powering RC mini gliders. I made it for a "Multiplex Solius Mini" but it should fit in most any foamy glider of similar size. The EDF pulls itself upright when power is applied and...

I made an adaptor that lets you power your RC mini gliders with a folding EDF, perfect for flying them around with a Multiplex Solius Mini - it'll fit any foamy glider close to its size just fine. When the engine's turned on, the EDF snaps itself up,...

Container for ballast and all electronics holds pivotal role in flying wing RC combat gliders. Witness raw combat action in this example video: https://www.youtube.com/watch?v=mu6tZX8V-LM Every component is strategically placed for easy access and...

This mount was designed with the Carrera Trimmy, Robbe Rotario, and Multiplex Domino gliders in mind - vintage models known for their weight, typically ranging from 1500 to 2000 grams when equipped with a 2200 3S lipo battery and motor setup. For...

Multiplex Minimag RC Plane Landing Gear Holder for Replacement When Damaged. ... This landing gear holder is designed to serve as a replacement part for the Multiplex Minimag RC plane in case the original one gets damaged.

Designed to fit narrower composite F3x, F5x RC glider fuselages (Nan, Vladimir, Jaro Mueller, etc.), this innovative tray recesses the Rx and tail servos back for increased space and simplified access to battery and electronics under the canopy. Two...

The Fox by Multiplex (https://www.multiplex-rc.de/produkte/854289-fox-rot/weiss-ve1) is an affordable EPP foam model glider, which some users have successfully converted for remote control flight as a glider or motorized plane. After watching videos...

Gassaway’s original design is here: http://georgesrockets.com/GRP/LaunchGear/Glider_Tower.html . I apologize that they are a mixture of metric and American, but I live deep in the hear of darkest American where most hardware is S.A.E. At least the...

GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mountThe gopro is behind the cw, check the cw from your funcub before the start.With a hot air blower you can bend wing shape, but it is not necessary, bracket is...

FunCub GoPro GoPro_Mount MPX MultiplexVersion 3GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount.The center of the GoPro is over the CW (ca. ...80mm)A recess for the ttow release available.With a hot air blower you...

Version 3GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount.The center of the GoPro is over the CW (ca. ...80mm)A recess for the ttow release available.With a hot air blower you can bend wing shape, but it is not...

Version 3GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount.The center of the GoPro is over the CW (ca. ...80mm)A recess for the ttow release available.With a hot air blower you can bend wing shape, but it is not...

GoPro Mount for Multiplex's FunCub Version 3 - Mount your GoPro in seconds with ease. No need to mess with the wings, just screw it on. The perfect spot: Place your GoPro right over the center of rotation (about 80mm) and get a bird's eye view...

GoPro Mount Version 3: A Perfect Fit for RC Funcub from Multiplex Mounting the GoPro on your RC Funcub just got easier! With this new version 3 mount, you can securely screw it onto the wings without any hassle. The center of the GoPro is precisely...

Here's how to get started with the GoPro Mount for your RC Funcub from Multiplex. Simply screw it into place on the wings and you're good to go - it's a breeze to mount. Before you start flying, make sure to check out the cambered wing (CW) of your...

GoPro Mount for the RC Funcub from Multiplex you can screw with the wings, easy to mount The gopro is behind the cw, check the cw from your funcub before the start. With a hot air blower you can bend wing shape, but it is not necessary, bracket is...

Mounting an affordable brushless motor from Big Dot Unclestore (product id: 139) on your Multiplex Teddy plane enhances its performance. The motor, when powered by a 2S lipo battery, significantly boosts power while shedding several ounces of weight....

I mounted a Pylon on top of my Multiplex Super Alpha (aka Nimbus) from 1977 GFK rc glider using a 6 mm bolt. I drilled the front hole up to 5.5 mm, then screwed in the 6 mm bolt and cut off its head, leaving just enough thread for attaching the...

Motormount for RC Gliders Turnigy Aerodrive 35XX Motor. This mount is significantly smaller than previous versions, featuring two plates with five holes that measure just 36 x 33 mm and are a mere 4 mm thick. The round component has been streamlined...

This is a motor mount for my Multiplex Alpha vintage glider. It's designed specifically for a 3536-1050 Turnigy Aerodrive motor and a 12x6e folding prop, but you can use any other 35mm motor as long as the hole spacing remains the same. Just place it...

I had to replace a few props, so I decided to make my own. I was dissatisfied with the designs available online and my broken propeller needed remodeling, so I created my own. After refining my design for hours, it's finally complete. So far,...

I'm planning on installing a multipurpose wall mounting system for my Twinstar model airplane, and it should be compatible with various other aircraft as well. ...The depth of the mounting bracket from the wall surface is approximately 3.35 inches.

We have some chairs which have a metal rod on the bottom, they have these gliders which prevent scratching. Some of these gliders broke so i designed a new one, this fits 10mm rods but you can scale the model to fit your chair. ... I would print it...

The "Phenix Glider Wings" provide an innovative way to enhance your flying experience, allowing you to soar through the air with ease and grace. These wings are designed for ultimate performance, giving you the ability to glide effortlessly and...