multiple tablet mount 3d models

**Work in Progress** I wanted to mount my tablet in my car as a new headunit. I took this A7 case and modified it for this mount. The holes in the back are for fans. I designed this for my 2016 Subaru Crosstrek. So it should fit similar years...

This model is designed to fit a Vizio xr6m10 tablet (5.5 x 3.5 x 0.2 inches), but you can easily update the model to work with other phones/tablets by tweaking the [Tinkercad...

However, the mount has enough clearance that even with socket head screws, the screw head stays away from the back of the Nexus tablet. Once flat head screws become available, I will switch to them. I also designed new versions of Mount_Top_Open...

Tablet mount for the driver side roof of my Polaris RZR Pro XP. The bolt pattern should fit any Ram mount that uses the ARMS bolt pattern. My machine has the factory plastic roof and unknown brand windshield. It may or may not work with other...

This is a tablet or Microsoft Surface attachment for the Reebok treadmill.

need to get your tablet off the table, hopefully this helps UNTESTED

Tablet holder extender specifically designed for use with tablets larger than 10" and DJI Inspire/Phantom controllers. This innovative design features a recessed area that can accommodate up to 12mm of foam tape, providing essential protection for...

Connecting element that can hold two tablets/portable monitors at once.

It has a "sliding hole" where you can fit a M4 screw in, in order to adjust the height and the angulation of the other piece;- the right side mount, where the tablet will sit on, has a hole for a M4 nut (it has a tight fit, you may need to apply a...

- The right side mount, where the tablet will sit on, has a hole for a M4 nut (it has a tight fit, you may need to apply a bit of force in order to slide it in). You can use this nut and the screw in the other piece in order to adjust this piece so...

This is a simple tablet mount for the Creality Ender 3, and also the Creality Ender 3 Pro. I have a Raspberry Pi inside my Ender 3 with OctoPi, and I had this old tablet lying around, so I thought to put it on the 3d Printer with Printoid in order to...

Wall mount for the [Lenovo Tab M8 tablet](https://www.mediamarkt.nl/nl/product/_lenovo-tab-m8-2gb-32gb-platinum-grey-1644556.html) used to display a Home Dashboard using the [Home Assistant Android...

I used this to fix my KoLasels tablet mount since its nut broke apart. The printed one looks more massvie than the original one, but since it's well hidden and since it's an important part of the whole device I care for robustness. Lets see how...

Also don't forget to also check out our video on the making of this remixed phone and tablet tripod mount at https://youtu.be/CvfyftuM_-Q Don't forget to check out our website http://www.DIY3DTech.com for more information on this project as well...

This is a versatile universal tablet stand, utilizing a standard GoPro mount as its base.\nThe device can accommodate gadgets with heights ranging from 155mm to 190mm and widths starting at 135mm.\nA cable clip has even been incorporated into the...

The holders have been in use for the past 2 years now, holding everything from IPad to Switch to Books … ## Instructions (copy/pasted): Since I mainly remixed parts, best explanations can be found with the original items: ###...

However, if you plan on using your truck for extreme off-roading, I recommend securing the tablet with adhesive or magnets as originally planned. I'd consider this design a success, but I'll continue to test it further. ...In warm weather, the PLA may...

-The 3 contact points with the tablet are improved for better grip on the tablet to prevent it sliding sideways -Alignment rails between riser and tablet arms to keep table from spinning around the bolt -The teeth between the two arms has been...

... of the transmitter. For the core mounting structure, I utilized 12mm aluminum tubes, which offer a cost-effective, lightweight solution that can be easily cut with a small hacksaw. ...I have also incorporated my design for the Lightbridge mount.

I widened the section on the hook to use when the tablet is in a thick case. ...There are 2 versions, one for an 8" and one for a 10" tablet.

This is sized for an older, Lenovo (S2109A-F) Android tablet, but should work on many others. I use three. Two on the bottom and one on top. Print Settings Notes: Print on side. ... Category: Tablet

I replaced a traditional tablet holder with a new one that perfectly accommodates my 7-inch Toshiba tablet. ... The inner space measures 120 by 12 millimeters, offering ample room for the device.

I wanted to have access to my phone or tablet while watching TV on the couch Easy print

Change Fusion360 model to vary size for any tablet!Original design: https://www.thingiverse.com/thing:4837454See instructions below

Depending on the size of your tablet you will need to print 2 or 4 of these.

designed to fit a HP premium keyboard. ...on top a tablet or smartphone not larger than 11 mm would fit

... as kitchen display for chef. It's for 6mm thick kitchen back wall glas and holds also mobile phones. I designed one version with 13mm, for iPads with protection case and one version for 17mm tablets and also the angle is a litte more oblique.

Additionally, I updated the rubber band mounts to work with a wider range of lengths, allowing them to loop through the top and stretch to various lengths on the hooks. Everything is oriented exactly as I printed it. ...To print it, I used supports...

I wanted a reliable, repeatable way to assemble and break down the tablet mount without using screws. ...I took the side braces and top plate and cut in a hole for a 8mm x 3mm neodymium magnet that I picked up at Lowes or Home Depot.</p> <h3>Print...

The wall support had to be invisible and mounted over an already placed 503 Box (Where was previously installed a wall thermostat), so inspired by other already posted projects I've decided to design this. It has room for 2 magnets (I've used...