mtc chassis 3d models

I've always like these hover tanks - so I decided to make some more modern/ BT modern looking ones based on the same chassis as per the TRO descriptions. I wanted a more "race car" like version of the Saladin as well as a more realistic armored...

It mounts a modified Schwerer Heinrich 150mm cannon on the armoured and highly mobile chassis it shares with the Baldur APC, the Sigurd MBT and numerous other vehicles. The Schwerer Heinrich's shells' weight requires the shells to be seperated into...

you drop the chassis in the bottom half of the ring and then stuff as many bb's in the race as you can. there should be a small gap... I think it's around 30 of them. then stick the top half of the ring on. I used some little 1" spring clamps that I...

A distinctive feature of this vessel is its opening mechanism and entrance, which allows the entire chassis to shift forward, accompanied by extensive cockpit windows. Intended as a guidance ship for larger vessels, the UPC - Dartwader lacks a jump...

It's worth noting that the chassis may not hold an electric motor when scaled down from 1:24, as it is sized correctly for that scale. I've included a slot car guide along with the model and a steering wheel. In due time, I'll add car rims and tires...

EDIT : 26/09/21 I have added the correct for for the chassis as the original one supplied was the wrong one, sorry about that. I have also added a support for the slide bar end, not that it needs it if you glue it into the cylinders, but it is there...

- Some features: a) Front and rear overhangs are minimal (almost none in comparison to the chassis) in order to maintain maneuvrability b) Front is designed to capture the most air for every cooling system inside, there are no other intakes...

There are M3 holes on top and at the back of the chassis, allowing for easy installation of the tachometer and wheel on both sides.\r\n\r\n24.12.2018 The second upload was the robot_board.stl file, a generic robot baseplate. Print settings were 0.3mm...

It is based upon the venerable Demolisher tank chassis (and the model is kitbashed/remixed from various files available on Thinigverse). I actually put some considered thought into designing this vehicle. It is modeled in concept on real-life...

Body can be fixed to the chassis by glueing strong magnets. You may reach the parametric design files from [github repository](https://github.com/mehmetsutas/Rigid3D-Anka-RC-Short-Course-Truck). ... [Here is a test run of...

Custom Elite Dangerous version of my [Corsair iCUE 4000X Front Panel design](https://www.thingiverse.com/thing:4889085) showing the 3 base Elite badges, Combat, Exploration and Trading (from top to bottom) This will fit the Corsair iCUE 4000X &...

... There's a component called BLOCK, which serves as a connection piece between the three chassis parts, facilitating alignment. ...After several attempts, I found the ideal size – 98% of the original measurement – at which it fit perfectly.

It utilized a basic chassis similar to their larger WorkMechs and appeared straightforward with a powerplant, gyroscope, cockpit, and other critical systems housed in an "armored-box" mounted on reinforced, armored "bird-walker" legs. Only through...

A new rear chassis with a stronger motor mount has also been introduced. Update: The rear axle has encountered issues with some users, prompting me to create a brand-new version. Update: A Facebook user discovered a thin wall on the front body...

Printing requirements: Chassis: 2 units Flight Controller Mount Bottom: 1 unit Flight Controller Mount Top: 1 unit Arms (unmirrored): 2 units Mirrored Arms: 2 units Landing Feet: 2 units Washers: 8 units Battery Tray: 1 unit Example build...

Wanted to mount my Sand Scorcher shell on a DT-02 Chassi so i whipped up these body mounts. The front one mounts over the front shock tower brace and down in the bulkhead with a single screw, the post then attaches to that using two m3 bolts+nuts,...

I trimmed down the mount post for the front shocks on the tower and the front arms 2-3 mms to move them backwards a little and allow the body not to rub on them, otherwise there are no changes to the actual chassi. Front post mounts to the original...

Power full and nice range distance .A perfect chassis to start rock climbing, with many possibilities of improvement and easy to prepare. Youtube Video aviable here : https://www.youtube.com/watch?v=hcnbGI2HpUM HSP Model : 94680T2 rock crawler ,a...

... is quite simple. Just place the bolt inside the spring and use a washer to secure it. Then, insert the "spring barrette" into the "spring holder" and adjust the spring as needed. KEY COMPONENTS M548 Chassis. M548 Gearbox. M548 Body 1/3 (Front).

A towing strap modified with loops at either-end is fitted as a bridge between the chassis catch bolts on each of the sliding doors. This is used as support for the second unfolded surface. Both doors still securely lock whilst the strap is attached....

There were two vehicles: IMR-1 and IMR-2, which are pretty much the same but based on different tank chassis (T-55 and T-72 respectively). You can find a lot of videos of these vehicles working in the containment zone, and even in front of the...

Features: Sturdy Chassis: The table is built to securely hold a platform using M8 screws threaded into the "Inner Part" of the design. Tube Connectors: Included in the files are connectors designed to fasten tubes with an outer diameter of 26.5cm...

Human: NOTE: V2 uploaded with sections of the chassis hollowed out to reduce weight (bot was approx 8 grams overweight!). This is an Antweight (150gram) pusher combat robot which I've called Scrapper. This bot was designed as the first of three...

In its original capacity as the basis for several tank designs, including the Jagdtiger turretless tank-hunter, the chassis employed in this heavy armor featured advanced suspension technology designed by Porsche and Henschel. Upon first entry into...

I also wanted to improve the case mounting points based off of [Jack Werner's remix of the original design](https://www.thingiverse.com/thing:3967425) Improvements: * The camera ribbon cable takes 90 degree bends in order to save on space while also...

The ribbon cable for the pi camera nicely routes out the right side and down below the chassis without interfering with the print area or prusa cables. ...The USB cable also routes nicely and leave the micros SD card up at the top for easy...

RC Dakar truck MAN Chassis: Axial SCX10 II Scale: 1:12 Dimensions: 540x320x216 mm Filament: 1900/2200 g Printing time: 140 hours approx. Dakar rides a fast assistance truck or racing truck. The assistance truck is the same as a civilian truck and the...

I solved this by adding a small spacer to the Extruder chassis so it hits the Endstop first. This piece allows you to attach a square nut to trigger the sensor. 3. Another issue caused by the conversion of the Mosquito is the Fan duct. I used a fan...

This IR LED light includes 2 high powered 3 Watt LED emitters potted into an aircraft grade aluminum chassis that is designed to protect the LED and dissipate heat. Even after running for a several hours, the lenses are only mildly warm.The value...

It's based on the same chassis as my mini Sumo robot. It boasts several key features, including: Controlled by a Raspberry Pi ZeroW Two analog reflection sensors A laser TOF distance sensor An AVR microcontroller for power management and analog/IR...