mr2 3d print

Inlet flange for 4AGE Toyota MR2 supercharger

Inlet flange for 4AGE Toyota MR2 supercharger

Cover, Rear Suspension Support:Toyota MR2 / MRS 1999-2007 Original part no.: 48753-17050 Test printed on:Prusa i3 MK3 @ Prusa Mini+ Disclaimer: This is NOT original part. It's been (re)design to match OEM part with my best ability. It's been tested...

Climate control air conditioning decorative gauge ring ZZW30 Toyota MR-S MR2 Spyder climate air con rings Dia 65.6mm x 6mm high, bevel taper Print 3 off, attach with mounting tape or dots of hot glue STL coming today

Cover, Rear Suspension Support: Toyota MR2 / MRS 1999-2007 _Original part no.:_ 48753-17050 _Test printed on:_ Prusa i3 MK3 @ Prusa Mini+ _Disclaimer:_ This is __NOT__ original part. It's been (re)design to match OEM part with my best ability. It's...

Cover, Rear Suspension Support: Toyota MR2 / MRS 1999-2007 Original part no.: 48753-17050 Test printed on: Prusa i3 MK3 @ Prusa Mini+ Disclaimer: This is NOT original part. It's been (re)design to match OEM part with my best ability. It's been tested...

Engine Bay Rod Bracket for Toyota MR2 Spyder/ MR-S

... friction fit snugly between the radio and shift console of my car. It's a simple design, but it works as intended. To ensure this gadget withstands the heat, print it out in ABS or PETG plastic when you plan to use it during warm weather periods.

These are the center panel brackets and tab for a MKII Toyota MR2

Engine vent ornament for ZZW30 MR-S MR2 Spyder engine cover vent grille Use shortened file for 350mm bed size (ZZW30_Vent_LEFT_12mm_shorten.stl) This file is 12mm tall so prints quicker than 16mm tall version Else print 2 sides in 2 half pieces (4...

Replacement headlight and wiper knobs I designed for my MR2 - printed them out of black PETG with 0.4mm nozzle and 0.2 layer height. I have been running them for 2 years now without issue except very slight warping due to heat. May need to shim the...

When removing the tail lights on the MR2 the holding clips break really easily, so I made this replacement for the outer piece. To remove the original clip from the car just remove the center screw, and gently bend down the clip until it pops...

These brackets will let a 4" Speaker fit on the rear of the MR2 replacing the original speaker and bracket. Possibly you could fit a bigger speaker but being so close to the passenger ear it wouldnt sound to well. I fitted some JBL Stage 2 424 easy.

Er passt perfekt! Hier der Link zu meiner Inspirationsquelle:https://www.printables.com/de/model/40807-hormann-protect-cover-for-remote-controler/comments/306471# It always bothered me that I had to look for the Hörmann HSE 4 BiSecure...

Adding a CAI can unleash its full potential, but it's crucial to do it correctly. Simply relocating the MAF to a larger tube won't suffice, and many people prefer retaining the stock intake assembly rather than creating their own due to difficulties...

nearly there! ...this one has the Sportivo splitter and rear wing

my 1st attempt at modeling a complex shape. sizes are just about correct. ...I own one so could check the thing as I modeled it.

1/64 scale https://youtu.be/ab9xatO-Njs

AW11 gearshift bushing

Customized version of https://www.thingiverse.com/thing:2949739 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2949739

A makeover for my spouse's car has become a topic of conversation lately. However, if the new color turns out to be an unfortunate choice, it might lead to some serious repercussions - even divorce is not off the table! ...But let's hope that doesn't...

modefied car

Cap for the front strut tower on the SW20.

modefied car

For the knob to change intake or recirculation. Just a press-fit no glue required. ...Also does not have the vertical piece that changes light.

You're basically getting a splitter ready to use, but more importantly, you get the bolt pattern. Feel free to add any shape of front lip you prefer. ... To mount it, you'll need: 3 pieces of M6x45 bolts 3 pieces of 22mm spacers 9 pieces of 6.2mm...

I've been working on a new line of upgraded models that I'm really excited about, and I have to say, they're looking better than ever compared to their predecessors. ...I plan to keep pushing forward with these updates for quite some time.

Here are some specs for this model: * Body style: 2-door coupe * Engine: Toyota 3S-GE inline-4 cylinder * Transmission: 5-speed manual or 4-speed automatic * Drive type: Rear-wheel drive * Length/width/height: 172.8 / 69.9 / 52.6 in (4390 / 1770 /...

Toyota Mr2 Mk3 Transmission Tunnel Centre Console There are 2 options, you can open T_final and divide it by your own. or you can use already divided parts. I was printing it with Anet ET5X (not on the list) printer, it required 300x300x400 working...

i took the measurements off of my Toyota MR2, so you may have to do some extra work to make it fit. ...i will upload the Fusion files as well.