mp mini select v2 3d models

Cable organizer designed specifically for MP Mini Sla printers, utilizing a minimalist approach by printing without a raft or supports. The part features a 20% infill density, providing an optimal balance between weight and structural integrity. ...To...

I drew inspiration from both designs - http://www.thingiverse.com/thing:143410 and http://www.thingiverse.com/thing:1071695 - to craft a Tensioner specifically tailored for the MP Mini. So far, it seems to be functioning smoothly. I encourage you to...

I remixed this model from HugoHuge to work with my MP mini delta. The roller is the same. ...This slides over the existing spool holder that comes with it and if you have a small spool you can always slide it off and use the original. Print Settings...

I've yet to validate this, but as I was creating a new SKR 1.3 mount for the MP mini delta, I ended up with an unfinished deck. Feel free to use it however you like - customize it as needed. TinkerCad is all you need for this project. Hopefully, it...

This sleek design for the MP Mini boasts a comfortable, rounded grip and elegant sweeping curves. For a similar aesthetic, check out the Architectural spool handle here: https://www.thingiverse.com/thing:2892791 I drew inspiration from...

This is a custom fitting for the MP Select Mini blower fan.\r\n\r\nFirst, remove the outdated fan by unscrewing all four screws and carefully cutting the wires. Next, insert the new fan into the adapter and reattach the wires with solder. \r\n\r\nYou...

I have the MP Select Mini Pro/V3 and recently bought a PEI sheet after hearing countless people suggest it. However, every spacer I found was designed for glass beds and too thick for my printer to perform a proper alignment. I borrowed the handle...

This is a motor mount and bearing block for installing a nema 17 and T8 lead screw on the Monoprice Select Mini. Note: you will need to cut the metal surrounding the motor if you use the z spacer like me. ...This is easily done with the Dremel and...

This is a custom motor mount and bearing block designed specifically for installing a NEMA 17 stepper motor and T8 lead screw on the Monoprice Select Mini 3D printer.\r\n\r\n\r\nImportant Note: When using the Z spacer, you'll need to carefully cut...

This converter transforms the Monoprice Mini 3D printer into a high-precision plotter, drawing inspiration from earlier designs featured on Thingiverse.

-------------------------------------------------------------------------------------------------------------------------- Update 4: Here is my configuration file for Slic3r Prusa Edition, which has been working seamlessly on my Monoprice Mini...

Give proper credit where it's due: I created this by modifying seagas' modified version of auralgasm's "Better Dial for MP select mini v1". (links below) https://www.thingiverse.com/thing:1692885 - seagas https://www.thingiverse.com/thing:1677768 -...

As I installed the larger bed, I encountered difficulties securing new pulleys onto the shafts that are solidly attached to the Minis Case. In frustration, I ended up stripping one of them completely and subsequently removed the other as well.

One is a frame with removable feet that fit snugly into it, and it's oversized, far too large for the Mini to handle on its own. But we're not out of options just yet. Foot_wHole is cleverly designed to utilize one of the screws that hold the base...

Even after my last modification, I still wasn't satisfied with the noise reduction of the base fan in my Monoprice Mini Delta. I remembered what needed to be cooled at the base of these printers: it's the aluminum heat spreader, which is glued onto...

This replacement knob fits the $199 Monoprice Select Mini, an improvement over the original due to its gripable sides that make rotating it a more comfortable experience. The new knob extends past the printer's front edge, allowing for easier control...

A handy gadget to carry all the essentials for the Monoprice Select Mini.

... top of the printer to have a straighter feed for the filament. I keep it there with a few small magnets under the spool holder. Simple and works well. Print Settings Printer: Monoprice Select Mini Rafts: No Supports: No Resolution: 0.1 Infill: 30%

This is a scorching hot end overhaul for the Monoprice Select Mini V2, complete with mounts for two blowers that will supercharge your 3D printing experience. Once I've finished writing up this instructable, I'll share it with you. To bring this...

More information and the model can be found at its original location, which is located here: https://www.youmagine.com/designs/mp-select-z-axis-bracket. ... I did not create this part and I believe that sharing it does not violate the thingiverse...

The Monoprice Select Mini ships without any fan protection, making this upgrade absolutely crucial. ...I've successfully used it on my Monoprice Select Mini Pro from 3D Print Things and the fit is absolutely perfect.

You can view the original design here: https://www.myminifactory.com/object/replacement-z-axis-assembly-for-monoprice-select-mini-v1-52822 I printed this model using PETG with 100% infill for added structural integrity. Update 11/14/18: I've since...

Place your Monoprice Select Mini V2 3D printer in front of a wall or other stable surface, making sure the print bed is level and clear of any obstructions. Position the webcam mount above the print bed, adjusting it as needed to get a good view of...

... should have been 14mm apart, so now it fits better. I also adjusted the angle from 30 degrees to 26 degrees and widened the edge around the nut bracket. Print Settings: Printer: MP Select Mini Rafts: No Supports: No Resolution: 0.2mm Infill: 25%

My MP Select Plus came with the upper X carriage rod holder damaged - possibly why it was a discounted open box, although I'd have thought they would check the basic parts properly. Before sending it back, I decided to try making a replacement using...

If you print this out and like it, I'd appreciate an "I made one." Print Settings Printer: Monoprice Select Mini Rafts: No Supports: Yes Resolution: .13125 Infill: 50 Notes: Print the mount on its end with the closed end down to minimize supports...

A custom-made plate featuring a precisely engineered hole that perfectly complements the Monoprice Mini Select, intended for seamless attachment at the base of a high-performance spinner system.

This modification secures perfectly onto the extruder feeder nut situated at the pinnacle of the tower, specifically designed for the Monoprice Select Mini. ...Successfully implemented by utilizing a brim and support structures.

Print Settings: Printer - Monoprice Select Mini Rafts - No Supports - Yes Resolution - .15 or .1 Infill - 100% Notes: Slicer - CURA The file may be very small in a slicer, so just scale it up to 1000%. This is a prototype, please let me know how well...