movo shock mount 3d models

I have a MOVO shock mount that I adapted to use with an Elgato Wave 1 mic, but it felt too floppy, so I designed a little extra support. I used a little hair band as the elastic part. Printed PLA at 0.2mm with 100% infill and a brim. ... I was able...

I was looking for a shorter mount where I didn't need an adapter for the mic shock mount. Modeled the post and then slapped the camera mount that Jschro36 uploaded on top. Works great. The post is about 1/4" or 7mm dimeter and might work on...

Coil SPrint Shock Mount

This acts like a bit of a rod end for Team Associated shocks. ...Great for Crawlers.

OVERALL DIMENSIONED SHOCK MOUNTS OF SIZES. ...AKCC SERIES

Basic shock mount for any microphone: - Tripod feet ending in points to minimize contact with table - Stretch rubber bands over the two ends of the mount - Put your microphone through the mesh of rubber bands at the top and let it rest on the mesh of...

A vital part of a vehicle's suspension system, the shock absorber helps maintain stability and control by dampening the effects of bumps and uneven surfaces on the road. ...This essential component ensures a smooth ride for passengers while also...

Just an update of the MOVO blinp microphone mount to fit the Rode NT4 microphone.  Design with DesignSpark Mechanical (Free software)

Just an update of the MOVO blinp microphone mount to fit the Rode NT4 microphone.  Design with DesignSpark Mechanical (Free software)

CVA SHOCK SPRING MOUNT

Scx24 dual shock mount

scx24 rear shock mount outboard

L22 Shock Mount from Barry Controls catalogue

Top shock mount for rear leaf springs in trucks

Human Factor Redesign of CVA Shock Spring Mount System

This is a shock mount for the tamiya lunchbox for after market shocks and 5th shock option will add more pic after i print one and install

This is a boom microphone shock mount. ...Use elastic bands or o-rings for moutinging

CAMEO - Movo Beam 100 & Movo Beam Z 100

Shock mount bushing engineered after RC10T bushing design, thoroughly tested to ensure compatibility with RC10T4 as well.

(8) Shock Mount TPU PIECE Hardware requirements: (20mm M3 Standoffs, 7 pieces) (M3 Washers, 16 pieces) (12mm M3 Screws, 8 pieces) (M3 Nylock Nuts, 8 pieces) (10mm M3 Screws, 14 pieces) Paracord (color of choice) is needed for damping vibrations and...

... onto roll bars using standard GoPro mounts. The case includes a GoPro HD HERO 2 Housing, GoPro Quick Release Base with a flat bottom, GoPro Quick Release Mount - Standard, and RC Shock Absorber HSP 286004 - 85mm for effective shock absorption.

A shock mount helps to prevent excess sound from your desk or recording platform from echoing into the microphone by dampening the vibration. ...The shock mount designed by the company can cost almost as much as the whole microphone itself which is why...

Pencil mic shock mount. ment for pencil condenser mics specifically the sE7 but can hold any 1" diameter mic. ...requires rubber bands and wing screw and nut.

Shock mount for a shotgun microphone which can be attached to IKEA TERTIAL work lamp. Longer screws are required and hair or rubber bands. ...

... which you can choose in your preferred color. This is the key component that enables the shock mount to effectively dampen vibrations and provide a smooth audio experience. ...You can easily find paracord at craft stores like Joann's or Michael's.

Secure your Shure SM58 mic in a shock mount by stretching rubber bands over opposite hooks and sliding the mic into place, sandwiched snugly between the hoops.

This heavy-duty shock mount features black hard rubber components for the main body, and stainless steel construction for other pieces to ensure durability and stability.

... of the Shock mount Microphone "Spider". ... Fits under the usual microphone mount, but adds anti-shock. You can print without supports. My seal was successful. ...(Anycubic i3 Mega S) Filling in 20% Modeling in the Russian program Compass 3D

A shock mount to isolate the recorder from the ground A shock mount to isolate a sound recorder. Needs a rubber band. A hair tie band will work just fine. PLA or PETG work okay. The bottom part has a plastic ¼ tripod mount you might need to...

... ~$8.00 USD to an online service for the parts to be cut from 6061 aluminum. Note that I'm using 120mm shocks and "1/10 RC Aluminum Front/Rear Shock Tower Hoops Bracket Mount for TRX-4". ... The longer shocks are not required, though the hoops are.