mouse mods 3d models

The utensil part of this device is detachable to allow for easier cleaning. Tools:- Snips, dremel, or an angle grinder (to cut the steel fork)- Needle nose pliers (to remove supports)Print Instructions:- 100% infill- 0.2mm layer height- yes...

You'll also need to make more mods to the rear of the blaster, and lose the screw post back there. Also due to the lower build quality, you may have to jiggle with the cage to get it to fit. I have found that they are all a little different. I have...

Print Settings Printer: Strongly modded Wanhao i3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Infill: 50 Filament: any any (High Temp like PETG or ABS advised!) Notes: optimized for 0.8 Nozzle (just make sure that Walls are sliced...

I know there is a similar mod that uses a MGN9 stand-alone, but these rails are meant to be mounted on a profile otherwise it is more then likely they won't be perfectly straight. Please note that I am actively working on this design, and this is...

-Also decided to try the Century 836 spring ( https://www.bunnings.com.au/century-spring-corp-22-2-x-101-6mm-compression-spring_p3970395 ) made famous by the Make Test Battle Sledgefire mod video, which I think is around 12 kg, performance is much...

It works but is a bit of a pain to fit, would do it differently next time but I wanted to keep the bottom as flat as possible and with good ground clearance. I used a large allen key through the holes in the bottom of the motor shield parts to align...

Note: The project relies on "stock" LED mod already installed, mostly for holding cables in place and also integrates with the wiring for LEDs to save on space. It can be done stand-alone without LED strips as necessary. Note 2: I'm partial about...

 If you appreciate what I'm doing, please consider buying me a coffee, and check out my other models!The X2 has the mods from my previous remix plus two others:Rotated flow splitter by 90° to help balance flow for left/right ducts - see rationale...

The exact list of extra materials - they are not too many - can be checked out above in the German section.I also enclosed the STEP files to let you mod whenever you need it.Nevertheless the construction is quite accurate an wil,l if printed well,...

- The X axis turns out to be a bit difficult because things look bigger in CAD than they really are :/ - The distance between the two X rods is only 27mm, yes, 2.7cm, not alot, I think the Anet A8 has around 40mm between the two rods which means that...

I do recognise that HorsEngineer's design makes more sense in the context of 2016 3D printing, though.Indexing post shortened, flush to hammer face to make it easier to align prints on bedThrow chamfers and fillets everywhere (Because it feels nice,...

If you're into modding, a stock blaster catch/trigger/lock spring could also do the trick provided it's the right length. More detailed instructions are included in the README.txt file. Enjoy the build, and happy foam-flinging. If anyone gets...

This is a remix of "Bondtech BMG on a Taz 4 (or Taz 3-5--needs slight mod for Taz 6)" by jaln". I appreciate how the design keeps things simple, integrates the parts cooler air duct effectively, and provides good visibility of the printhead. The...

The whole diorama and both models took a total of 225 hours for concept and modeling, and 52 hours for printing various failures, mods, etc. All pieces have been thoroughly tested to ensure they print out smoothly with ease. All of my models are...

Introduction:\r\n\r\n*** This mod blocks the vision positioning system (VPS). Keep this in mind, and you may want to disable VPS *** I personally have not had any problems. Please be safe with this project. Never fly a drone directly over people or...

This mod is highly recommended for probes using a normally open configuration, as crashes would be more likely (e.g. Piezo, BLTouch). Wire the switches as NC (normally closed). You can wire all three in series and hook up to one spare endstop (say...

I suggest the following 32dp (0,8 mod) gear ratio range to keep it fair against Tamiya M-chassis cars, with standard 540 motors: 54T spur 22T pinion for best acceleration and 28T pinion for highest top speed. 3D printable 32dp gears are included...

The sensor that got the closest to what I wanted is the SpEye by MirageC [thingiverse](https://www.thingiverse.com/thing:4299458) | [docs.hevort](http://docs.hevort.com/#/pages/Mods/spy-eye.md) The SpEye introduced too much friction in the filament...

Cynthia is a bolt action Nerf blaster that uses half dart Talon magazines! Firing Demo: Blaster Overview: https://youtu.be/mIW0dAyOCv0Customization Overview: https://www.youtube.com/watch?v=mZe6dWdQUs0Assembly...

My scratch build: 0802 Unibell 19kkv motors by Happymodel Nanohawk AIO modded with NLRC 400W vTX (disabled SPI D8 receiver) Flywoo EL24E ExpressLRS 2.4GHz receiver Solid pin PH2.0 battery connector HQ Prop 40mm triblades Caddx Ant 4:3 1S Optimized...

If Your Blowing The Right Direction Then All Should Be Fine With Cooling Air Streams Directed Toward Printed Object During Process Steps, While Ensuring Good Spinning Capability As We Designed In This Mod With Added Small Spacer Bars Keeping The...

However, other length belts will likely work as well. These pulleys for the Z rods (https://www.amazon.com/gp/product/B077GMKW1C/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1), and these idler pulleys for the tensioner...

This is a simple mod for your MK3 to use it as a penplotter. The main design objective was for it not to interfere with printing and to not have to assemble or disassemble any parts to change from one to the other.</p><p>I tested multiple designs...

Mods Upgrades Customized Parts Scalable If you noticed the motor and idler mounts to be placed in the corners of the frame. This eleminates any design constraints of overall length and width. So if you need a printer to be a specific size or you...

The whole diorama and both models took 190hrs concept and modelling, 71hrs printing various failures mods etc . . all pieces have been tested and they print out very easy as long as you follow the settings. .All of my models are only released when...

The whole diorama and both models took 225hrs concept and modelling, 52hrs printing various failures mods etc . . all pieces have been tested and they print out very easy as long as you follow the settings. .All of my models are only released when...

If you do make your own mod from within OnShape, please let me and the community know with the "remix" check. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Infill: 10% Filament: Hatchbox PLA Post-Printing ============= Drill...

Human: ** Kyosho Blizzard FR Dual 540 Motor Transmission **\r\n** * Works with SR, FR and FR 2.0 versions for sure, possibly others **\r\n\r\n* NOT compatible with standard plow lifting mechanism\r\n* Compatible with my modded plow :...

Also I suggest printing in PETg or similar flexible filament type * And the printer in use [Mini Stand is from this collection of Thingys](https://www.thingiverse.com/thing:1977933) * And my [OctoPi is located in this...

This mod gave me, with a clone Titan extruder, and clone V6 hotend, 145mm of vertical height. I can push that to around 155mm, if I don't home the axis before lowering it, and I choose to lose ~30mm of X. Bonus For Z, I have included an end stop...