mouse cord holder 3d models
383387 3d models found related to mouse cord holder.thingiverse
This is a low profile slim mouse cord holder for mouse cables <2.5mm in diameter.
thingiverse
You will need: Double sided tape This nifty mouse cord holder has 2 advantages to other designs! 1. You can stick it with tape wherever you like 2. The cord does not escape! Just adjust correct length and forget about it :) Enjoy! ...
thingiverse
This is a mouse holder that I designed to keep the cord off of my mouse pad. The hole is three-quarters of an inch, so it should fit any USB plug easily. To use this holder, simply print it out and place the legs under your mouse pad. Finally, feed...
prusaprinters
Stick it to the bottom of your monitor with double sided tape or hot glue to elevate your mouse cord and prevent tangles. If you'd like you can buy me a coffee here: https://www.buymeacoffee.com/junrenman
thingiverse
Just a 15 minute make I sketched up to hold the cord on my mouse so it doesn't fall off my desk. I didn't like the ones that were currently on thingiverse, as I wanted one that held the cord tightly, not just the end. I have a logitech G403 gaming...
thingiverse
A small, minimalist, wire holder, i have glued it place on my desk with double sided tape.
prusaprinters
A small, minimalist, wire holder, i have glued it place on my desk with double sided tape. Print Settings Printer: Geeetech i3 Pro B Rafts: No Supports: No Resolution: 0,2 Infill: 10% Category: Gadgets
thingiverse
I've always wanted to own a computer mouse bungee cord holder, but i didn't want to spent money on it, so i printed mine.
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515
thingiverse
Mouse Bungee F2 sostiene el cable del mouse para que se mueva libremente. El trabajo esta en progreso. debo hacer que sea mas pesado y mas adherente a la superficie del escritorio. Se puede probar usando una cinta adhesiva doble. Son 2 piezas...
prusaprinters
Print instructionsCategory: Computer Summary Mouse Bungee F2 holds the mouse cable to move it freely. Work is in progress. I must make it heavier and more adherent to the desktop surface. It can be tested using double adhesive tape. They are 2 pieces...
thingiverse
Reproduction of this cable claw with screw holes (M3) https://www.amazon.fr/Akwox-Organisateur-Management-Chargeurs-Téléphones/dp/B01KFQB5WA Five slots with flexible size: Design with 3pcs 5.0mm slots and 2pcs 7.5mm slots, flexibly fit large...
thingiverse
This was designed to organize the USB plug and cord for a basic Inland mouse. ... The notch for the cord may need to be adjusted if your cord is a little thicker.
thingiverse
Got tired of my extra cord from my mouse in the way so I made this! ... USE: Set desired amount of length for your use case and simply pull that section through the hole.
thingiverse
... and a half and shows no signs of damage or even wear. The bungee holds the cord in place, but can be very easily adjusted around, because the design allows it to be pulled through easily when pulled in a direction that is parallel with the cable.
thingiverse
A little twist clip for keeping mouse cords from becoming a rat's nest. It was inspired by muzz64's Tidy Tail (https://www.thingiverse.com/thing:2411911), but was created from scratch for the cable size and wall thickness I needed. (designed for a...
thingiverse
The cable on my mouse (Logitech G302) was also a little too large to fit into the groove comfortably, so, added a bit of a bigger inner channel for that to lay in. I found that the base also is really light, but, a bit of double sided adhesive made...
prusaprinters
The cable on my mouse (Logitech G302) was also a little too large to fit into the groove comfortably, so, added a bit of a bigger inner channel for that to lay in. I found that the base also is really light, but, a bit of double sided adhesive made...
cults3d
Flexible mouse bungee for attaching to the back of your table. Use TPU or similar for the rods, and PLA or whatever for the rest. ...I recommend 95A TPU.
thingiverse
Flexible mouse bungee for attaching to the back of your table. Use TPU or similar for the rods, and PLA or whatever for the rest. ...I recommend 95A TPU.
thingiverse
(Thingiverse 4352817 ) There are a few designs for Cord stops on Thingiverse but I did not find one that used a spring to keep things in place. There are lots of these on the internet for sale but they are a bit pricey, especially if you need more...
thingiverse
Made this for my Logitech G502 mouse, pretty sure it works for others as well! ... Cord Length of G502: 6ft.
thingiverse
this cord holder designed to fit all cords as big as or smaller than an iPhone cord
thingiverse
Cord holder for the bedside table to keep those pesky cords from falling behind!
thingiverse
Four Cord holder. Sized for standard PC power cords but will hold cords as small as a USB cord easily. ... **Please be sure to use only Flexible Filament!**