mounted vinyl 3d models

Having such a system allows for new mounts for other use cases to be easily attached without spending hours trying to come up with a different place to mount it. As the entire point of this project is to streamline the experience of adding new...

This model is a Reolink RLC-811A Camera Mount for 5" Dutchlap Vinyl Siding. ...It will print with no supports.I needed a sturdy mount for outdoor use so I printed with 4 perimeters and 4 top and bottom layers out of ASA.Mounting hardware:Camera to...

You can use this to display vinyl record sleeves on your wall as a unique decorative element. No additional support is needed, simply print it out as is! Check out the photo to figure out how many of each design you'll need to match your album...

With this setup, your vinyl records become a constantly updated art display, showcasing your favorite album covers on an entire wall. To use it, simply print out the pairs of brackets, measure the spacing required for your LPs, and mark the wall with...

I'd like to extend my gratitude to Devin Paul and his original Plotter/Vinyl Cutter Mount design on Thingiverse (https://www.thingiverse.com/thing:3422179). Please visit that page for his guide and give proper credit where it's due. NB. I found...

I utilized spare aluminum plates, cutting them to length (41.5mm) and incorporating them into the design to reinforce the printed part, as multiple records are stacked on one mount. It boasts a hollow central section, serving solely to connect the...

--- ##**Switching between 3D printing and vinyl cutting:** I designed this to be easy to switch between 3D printing and vinyl cutting. I designed it so the plotter will not interfere when 3D printing, so it can stay attached. All you have to do is...

I Took inspiration from https://www.thingiverse.com/thing:3628510 But I ended up designing my own, since I wanted a few extra things. I wanted two magnets (4 total) to handle the extra weight of double/heavy albums and I wanted a hole so I can screw...

I Took inspiration from https://www.thingiverse.com/thing:3628510 But I ended up designing my own, since I wanted a few extra things. I wanted two magnets (4 total) to handle the extra weight of double/heavy albums and I wanted a hole so I can screw...

This mount is not limited to vinyl records; they can be used for anything that is relatively light, thinner than ~0.4" (<=10mm), and able to balance on ~4.73" (=120mm) of shelf width. I printed this with the wall mounting face on the bed with...

This clip attaches to the vertical corner trim pieces on vinyl siding and is used for Christmas lighting to attach 1/2" PVC pipe. The pipe outlines the vertical features on a house. ...I had a hand railing that fell into place where the original put the...

I printed the record wall mount on the Ender 5 Plus. ...If your print bed is big enough, you shouldn't have any problems printing it without support and in one piece.

Human: Updated part from: https://www.thingiverse.com/thing:1489362 Same design with screw holes to mount, meant for use with 1.25 inch drywall screws without anchors. ...Please share your printed creations and impressive vinyl collections!

Remixed to fit my Geeetech A20T 3D printer and to be able to leave the bracket in place. I setup a dedicated machine in Cura with the relevant g-code and X / Y off-set, adjusted the Z off-set and used the attached cura profile so that it was easy to...

Just filled in the holes for the camera and the bolts.

Humanized by precision-crafted 3D modeling tools!

I created a modified design in Tinkercad, eliminating holes since I utilize Command Strips. Additionally, I developed an extended version suitable for thicker records. To achieve optimal results, I suggest rotating the design on its side and...

Redesigned to perfection, this innovative solution features a cleverly crafted angled hole that securely locks into the wall, effectively preventing any unwanted rotation. ...By doing so, it boosts the overall holding power to keep even your most...

I designed the layout to accommodate my entire record collection, no matter how extensive it may be. ...Furthermore, I incorporated two additional screw holes with a diameter of 3 millimeters to provide extra stability and flexibility.

Basic display stand with enough room to display a 3x gatefold. Secured at the rear with 2 command strips for added strength over some other designs that only use one. ... Command strips used: "medium picture hanging strips" printed with rafts and...

Print 4 of these and snap them together. Requires 2 nails/screws. ...If you find an alternative to nails, feel free to share.

Customized version of https://www.thingiverse.com/thing:6008830 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=6008830

Ender 3v2 Vinyl Cutter Knife Blade mount for BLTouch Use two M3x10mm or M3x15mm hex head screws Required X, Y & Z offset

This drag knife holder is designed to work with my [LEAD CNC generic mounting plate](https://www.thingiverse.com/thing:4849251) and holds on to the [V1 Engineering drag...

Remixed the LP wall mounts so that the back is flat. ...This way i can attach my double sided tape better.

Remixed post by @cyamate to have file already laying flat on print bed and also have 3 pieces in one file. ...Enough to mount 2 albums, which is all I needed.

After becoming frustrated with Cricut making the machine I bought my wife a few years ago completely worthless I decided to find a work around. blade mounts on the front of the print head and can be raised when not in use or easily completely taken...

Screw spacing is 1.5 inches on the blade mounting points, allowing for inserts for other blade carriers to be easily made. I cut from SVG files converted to GCODE using instructions from this instructable. Make sure that you enter the correct offset...

Simple great solution to display the record you are playing on your turntable. Holes designed for #8 x 1 1/4 screws but others will work and command strips can also be used. ... Enjoy!