mount plate for ambico v 0552 video tripod 3d models

Tripod Mount for Ambico 40mm. ...The other models were too big on thingiverse to fit into my tripod.

Tripod Mount for Ambico 40mm. ...The other models were too big on to fit into my tripod.

SummaryTripod Mount for Ambico 40mm. ...The other models were too big on thingiverse to fit into my tripod.

Replacement for the little rubber camera holder on an ambico tripod.

... angle is around 61.5° and 45mm x 45mm square. * You might have to adjust your printer to find the right size for your tripod so the latch holds. * Printed with 50% infill due to the pressure of the latch. * The dovetail angel is 64°. ...

This cheap camera tripod is used for various photography types, but it has only one mounting plate. The issue can be resolved through 3D printing. The mount uses a 1/4-20 screw for the camera attachment and includes a nut trap with an...

For a fairly late model Ambico branded, all plastic quick release tripod, does not have a geared crank elevator. This tripod might not have been worth to rescue but it's lighter than my aluminum tripods, and the quick release block is kind of...

Customized version of https://www.thingiverse.com/thing:2087895 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2087895

This Ambico Model V-0552A tripod ended up in my closet, and of course the shoe was missing. So instead of looking around here I made a quick, quick release shoe for it in Fusion 360. The part that mounts at the widest point is 44mm then tapers down...

20mm mounting surface for a Manfrotto video tripod.  Designed to clip onto the legs which are two 16mm rods.  The surface is designed to support a piece of velcro, or the model can be modified to hold an accessory.  I will be...

Replacement tip for Ambico tripod that extends to 41". ... Approximate measurements Outside(mm): 24x17x12 Inside (mm): 22x12x7

I made a sturdy tripod plate for my old Cullmann Video 3200 tripod. It's almost like the original plate but without the pin. Use a ¼" photo screw and a washer. I've added also the Fusion360 project and the STEP file in case you have to change...

I made a sturdy tripod plate for my old Cullmann Video 3200 tripod. It's almost like the original plate but without the pin. Use a ¼" photo screw and a washer. I've added also the Fusion360 project and the STEP file in case you have to change...

A simple mount to attache my ATOMOS Ninja V to my tripod. ...It's designed for a 30mm rod, but you can easily update that to fit whatever diameter you happen to have. The mount has a 1/4 20 hole to allow for the attaching of your NINJA V.

This is a clip-on mount which holds and Anker Power Port 6 USB Charger to a Manfrotto Video Tripod.  It is currently designed as two parts fitted for my Anker Power Port 6. This allows me to charge all the devices on my tripod (Encoder,...

This is my design for a 1.2-5.8 video repeater with a tripod mount. The design features removable lid, internal cooling, switches and a battery meter. I included cable cutouts if anyone would like to connect a backup monitor directly to the...

Small Bracket to hold V-Lock or V-Mount Batteries to the Leg of a Miller Tripod. Bracket has a thread designed into it to provide grip and stop sliding down the leg If your battery is really heavy thee is room to add PVC tape to the top for extra...

I used this to attach an art easel to an old tripod. ...I Had to shorten rricups alittle to get it to fit on the tripod mount " Quick Release Camera Mount for AMBICO / VELBON Tripod by schlem" top for adhesion purposes

This is yet another tripod mount for the HTC vive wall plate. (Because there is definitely not enough of them !) It is inspired by https://www.thingiverse.com/thing:1530209 but I wanted it to have a vertical plate so that the wall mount could rotate...

This is an Arca L-Bracket for cell phones to use with tripod. Features: Landscape and Portrait orientations. Walled slots on the underside to prevent unintentional slip. Supports phone (w/ case) dimensions: Width 65-95mm, Thickness 0-14mm, Length...

for horizontal and vertical mounting I used Velcro. ...It also works with a rubber band or a strap 4x 4mm screw

tripod mount plate

This is a mount for the Boscam RC832 video receiver for use on a tripod. It has a 1/4 x 20 thread included in the print. ...Print Settings Printer Brand: Prusa ...

After getting new tripods for my cameras I found that the original mount would not work with the new tripods. I designed this mount to clamp onto the upper portion of the tripod leg and the recorder just snaps in. Next I will be designing and making...

I needed additional mount for my tripod to use multiple cameras and camera slider, so I designed and printed it.. The video shows how I designed and printed this part. ... https://www.youtube.com/watch?v=bsoT3DosAQs

This assembly mounts the FS4 to the leg of a camera tripod. Instructions Printed with PLA, .25mm layers. Use 3mm hardware. I added a silicone pad in the back to cushion the recorder. Openings provide...

I needed a way to mount a 3s 2200 to V-Slot. This will slide in and let you run velcro straps around it. ...It fits a little loose, but it'll work.

I needed a way to mount a 3s 2200 to V-Slot. This will slide in and let you run velcro straps around it. ...It fits a little loose, but it'll work.

This mounting plate is used on a tripod to mount a 3" Lazy Susan bearing for full 360° free range motion. *please note- this is not a standard 1/4" tripod screw mount. It is an M14 that is specific for the tripod listed below* I designed it for...

This video is all about modeling, 3D printing, and building a small, lightweight plate for mounting V-mount batteries. This camera gear can be used with a 15mm rod clamp for increased utilization. Due to the material problem of 3D printing, it has...