motorola razr 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

THis also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

this model the reason I like it better is because it locks into place then you just press the button and it works so nicer better than the others hear that you just hold it in with pressure. Arduino program settings this is all new to me I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 35 stencil_pattern_element_shape = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

None of these models should need any support, I try to avoid them if at all possible, but you will need to be able to bridge somewhat decently. I personally used Overture Easy Nylon, it's very stiff for a nylon that doesn't seem to creep and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

One suggestion offered is to quickly wave fire under the problem area in the hopes that the hair will burn away before the plastic is damage, but I came up with a different solution.This set of models replaces the entire front wheel assembly. The...

MAJOR UPDATE [2017-05-05]: New and updated models were added based on suggestions and requests from people who have printed the terrain set (thanks abchiptop). Work log checked off... Checked all decks to be same dimension (5mm thick) - [x] Checked...

They come in hole (if you want to retrofit or use plugs which will not fit through the not holed ones and no-hole for initial build You will find most of the models also als thread insert versions, since I started to use melt in threaded inserts. ...

Initially I modelled the candle I wanted, then using boolean operations subtracted it from a cube, and split the cube in half. ...Then I added the pins and matching holes just to help align the boxes and hold them together a bit by padding and pocketing...

Check out the rest of furniture models from it, as they will fit nicely with this mini set! Bar pieces have special connections that allow you to attach them to each other in an unlimited amount of ways, and create any shape of bar that you desire,...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

This thing is a two-part shield for the head of your Ryobi trimmer, model number: RY40220. It’s a bit crude, and I planned on making it look smoother, but this thing really works! By narrowing the gap that the grass can fit through and diverting it...

Enjoy :) Update 04-05-2021: Adding ender 6 models, upgrading all to V4.3 (slotted mount holes for 2mm height adjustability) and adding "fan duct up V2" which has integrated grill. It's more tricky to print because of the small features so i'll leave...

Lastly, 5) It's ideal that any new design incorporates adaptability tailored towards various unique setups ensuring optimal calibration results across differing conditions allowing me customize freely as I work alongside other solutions which prove...

... tolerances must be around 2 tenths of a mm, it is not essential to use CNC systems. The pieces can be easily made by any turner or by a modeling enthusiast and their cost is quite acceptable. ... Criticisms, suggestions and changes are welcome!

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

Then it becomes matter of swapping the 5 tubes that lead to the MMU2S, but not to refeed the buffers each time.The model consists of two parts: a connector which is screwed between the upper and lower part of the body, and a bracket that holds two...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...