moto g power 2020 case 3d models

Moto G Power 2020 case, with a hole for the fingerprint sensor and some hexagons cut out to provide some texture/grip. Printed in TPU. ... Remix of this thing: https://www.thingiverse.com/thing:4425758 but because it's Saturday, or whatever,...

I noticed there weren't any cases available to print for the Moto G Power (2020), so I quickly created this design for printing in flexible filament. I then printed it in 4-year-old, very wet TPU on a printer with a Bowden extruder, and now I'm eager...

I noticed there weren't any cases available to print for the Moto G Power (2020), so I quickly modeled this for printing in flexible filament. I then printed it in 4-year-old, very wet TPU on a printer with a Bowden extruder, and since I am now full...

This is a remix of Zarlor's remix of the Moto G Power (2020) case. I added knurling to both edges to provide more grip to the sides of the case, and added corner bumpers to increase the drop protection. I removed the fingerprint sensor access hole...

I remixed the Moto G Power (2020) Case by kensikora. ... - added hole for fingerprint reader - added hole for microphone - added space near ear speaker for proximity sensor and ambient light sensor - added bar between volume and power buttons to stop...

I designed this printed magnifier 4x objective lens holder to slide over the following Otterbox case for a Motorola G Power (2020) cell phone I have: https://www.amazon.com/OtterBox-Commuter-Motorola-Retail-Packaging/dp/B082G2LC4W Frame printed at...

I designed this printed magnifier 4x objective lens holder to slide over the following Otterbox case for a Motorola G Power (2020) cell phone I have: https://www.amazon.com/OtterBox-Commuter-Motorola-Retail-Packaging/dp/B082G2LC4W Frame printed at...

This is a remix of mc88's remix of the Moto G Power (2020) case. I restored the fingerprint sensor access hole and added cutout to make the stylus accessible. ... Pictures of the printed case to follow.

A phone case for the Motorola G Power designed to be worn on the wrist. I was inspired to make this by the Pip Boy from Fallout. ...Simply use the provided screws to attach the 2 pieces, and put your phone in the case.

I call it a variation rather than remix, because I cannot install 123 Design on Linux, and have therefore re-designed the case from scratch in OpenSCAD using measurements from these two models. Unfortunately I cannot figure out how to get Thingiverse...

The Moto G Power 2021 is fairly new and few cases are available for it. ...Designed my own, and it was printable without support for all but the buttons and holes.

A case for the Motorola Moto G Power, 2021 version. Printed in PLA. PETG would probably work fine as well. I've printed this number of times and I'm pretty happy with it. File: MotoGPower2021Case_.stl --- I added a design for flexible...

I designed two cases one with Large fingers the other for small fingers. I used a Flexible filament TPU I have tested this for nearly a year with phone drops on floors and driveways and never broke the phone in any way. not like your cheapo phone...

Having the volume and power open makes it very easy to tell what orientation you're holding it in. I printed in TPU at 220C, bed 60C, I used a raft because my first layer wouldn't stick without it on the Creality Ender Pro 3. I did use supports,...

Just a phone case. Great in TPU. 0.16mm or less. ...

Moto G 100 Case for Moto G 100 made in PLA. ... Rigid Case

I recently acquired a custom-made Moto G case from Abrokadabra, giving their design a stylish makeover.

Moto G Power (slim case) Slide-in Charging Dock Sick of picking up the phone to unlock it (fingerprint scanner on the back) and wanted a bit cleaner look on the desk. Looked out there and couldn't find any charging docks for the Moto G Power so...

This is an updated version of the Moto X Case v2.0 designed by andrewSORG. The edges have been raised for added screen protection, ensuring that if the phone falls with the screen facing down, the case takes the impact instead of the device itself. A...

... room to the ID/debit/credit card slots so you can easily stash all your essential cards inside. For regular cases, you get a deep storage compartment that measures about 7mm, while our "deep" case gives you a spacious 12mm for maximum versatility.

Seems authentic! ...Will proceed with a trial print shortly. After that, I'll transform it into my official 'Cash Sling Cases' mark!

I'm thrilled to share that I've designed my first phone case, and after trying out different designs, I finally found one that fits perfectly. ...If anyone is interested in making this design a reality, please feel free to ask me any questions or...

this is my first phone case for a phone, i couldn't find one so i made me pone and the fit is great, any questions feel free to ask ask. If you guysmake this please post it, i would love to see what you guys do with it. CHEERS!! case with jack has...

This is a remix of dirtdigger's Moto G Power Case, modified to fit the latest Motorola G Stylus 5G phone. ...I used Hatchbox TPU (95A hardness) with 0.3 mm layer height, 2 perimeters, and 5% infill (see the 3mf and gcode files - for the MK3S+).</p>

Originally published here: Motorola Moto G x1032 case by tato_713 - ThingiverseSome of the models are designed for rigid materials and others for flexible ones.The models materials are not interchangeable, so pay attention to the file names. If you...

If you have any request on the design just ask me. For other phone cases check this. Here is the explanation of the files names: Flex: made for elastic filaments like TPU. Not tested.</li> <li><b>Rigid:</b> made for rigid (non-elastic) filaments...

For other phone cases check this. Here is the explanation of the files names: Flex: made for elastic filaments like TPU. Not tested. Rigid: made for rigid (non-elastic) filaments like PLA, ABS, HIPS, etc. The holes for the buttons are opened on...

The USB-C cable on my Moto G Power would constantly fall out. I designed this clip to keep it held in place. I've been using this clip for about one year and it has worked well for me. This may work for other Moto G phones, but I don't have...

Customized version of https://www.thingiverse.com/thing:4751664 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4751664

Printed with a brim at 40mm/s. ... Corners are in need of rounding in future updates or remixes.