motherboard with backplate 3d models

Human: Customized Version of Thingiverse Model Created with Customizer! ...Thingiverse URL Instructions Using the Following Options: image_size = 20 Move_Image_Left_Right = 60 input = none top_text_font = write/orbitron.dxf Bot =...

The specifications for this personalized version include a bottom text rotation of 0 degrees, an orbitron font for the bottom text label, a top text size of 12 points with the label "Dreambox," moving the image up and down by 50 units, left and right...

Created with Customizer! ... Instructions Using the following options: text_size_1 = 14 text_size_2 = 10 font_name = write/orbitron.dxf move_up_or_down_text_top = 59 machine_type = Rep2 text_label_1 = makerbot image_scale = 30...

Customized version of http://www.thingiverse.com/thing:118870 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=118870 Instructions Using the following options: bottom_text_size = 21 top_text_size = 12 Rotate_Image =...

Customized version of http://www.thingiverse.com/thing:118870 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=118870 Instructions Using the following options: bottom_text_font = write/orbitron.dxf image_size = 50...

The customization options include moving the top text 38 pixels left or right, choosing "Rep2" for the bottom text, shifting the image 61 pixels left or right, setting the top text size to 11 with a font of "BlackRose.dxf," adjusting the bottom text...

Human: Personalized rendition of http://www.thingiverse.com/thing:118870\nCreated with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=118870\n\n \n \n Directions\nEmploying the...

Next, insert the mounting bracket onto the deck, aligning it with the pre-drilled holes, and screw it firmly into place. ...Finally, attach the Scotty mount itself by sliding it over the bracket, tightening the screws until it's snugly secured to the...

The options used include bottom text rotation set to 0, no image rotation, moving the image up by 50, using orbitron.dxf for top text font, moving the image left by 60, setting bottom text label as "BLACKSMITHS," Rep2 as Bot, moving the top text up...

Attach this newly crafted backing directly behind your Jolt by carefully excising the outdated backplate, then firmly gluing it with a premium superglue such as Loc Tite - I swear, it works marvelously. ...What ingenious builds do you folks have in...

This print essentially just adds smaller diameter washers on the back of the motherboard to allow the pushpins to catch.I made this for an LGA1155 socket motherboard but might work for others that have CPU cooler mounting holes that are 75mm...

I reduced the footprint of the backplate by 2cm to make it a bit more compact to fit by my side-mounted spool on my CR-6 SE. Made for 3Mx20mm cap screws and nuts. ... Use desired top from the original design.

My design is made with a thin backplate, and a 1mm shim is provided, so that you can adjust the distance between the support and the gantry, to have a perfect fit with your machine. If you need to shim for less than 1mm, I'd suggest to use thin M5...

But you can try if you want :) ### Update ### + 20/05/2022 - added a second variant of the first panel, now you can add a [microSD card holder](https://www.thingiverse.com/thing:3164724) so you don't have to open your Amiga everytime you want to...

Align heat sink screw holes with holes in plate while simultaneously aligning all fang plate holes with those on the X carriage mount while paying attention to the routing of heat block wires. Screw in the two heat sink screws and then the two screws...

Align heat sink screw holes with holes in plate while simultaneously aligning all fang plate holes with those on the X carriage mount while paying attention to the routing of heat block wires. Screw in the two heat sink screws and then the two screws...

As IroesStrongarm mentions in his post, the bottom holes may be a bit lower than they need to be, and he used them with heat pressed M3 inserts. ...I'm posting this prior to actually printing it just as a way to save my thought process, but I may...

He just drilled a hole in his case, but I figured I could 3D print something so I didn't need to make permanent modifications. As IroesStrongarm mentions in his post, the bottom holes may be a bit lower than they need to be, and he used them with...

This is a Remix of https://www.thingiverse.com/thing:3030160 & to mount the Pi-Fan 30mm on the back of the Octoprint console and I made two type of screws so that it can be fixed both in one direction and in the other . ...

Remixed to have thinner edges as I needed that so it would fit on my build plate.

Remix from https://www.thingiverse.com/thing:2714420

This design boasts a compact ethernet connector and a thinner profile, shaving down the entire plate to just 3 millimeters. ...Furthermore, airflow efficiency has been meticulously fine-tuned for superior performance.

Realistic radio model from the 50s. ...(1956-1957)

Royalty-Free Icon from Lucio of Overwatch\nIcon Measures 100mm in Length Total\n82mm Icon Dimension, 7mm Total Thickness\n6mm Thick Icon Material\nNo Backboard Version Available at:...