morse code bit 3d models

... Share a couple of the students’ creations with the class and talk a bit about the capabilities and limitations of 3D printing. Would these designs be printable? Would support be required? Should it be printed in multiple parts and then assembled?

- TOP SQUARE SHORT: as above, but it's a smaller part and the filament path is a bit more aggressive. - TOP ANGLED: mounts the same but is angled 45 degrees and puts the filament further from the printer. All three top mounts have an additional two...

The quadcopter started to feel a bit weaker as I approached the 5 minute mark, but it was more than usable at 6 minutes of air time. You can run 3S batteries if you already have them, but I highly recommend the 850mAh 4S. I have 5 of them, and...

Also the magnet based mechanic feels a bit gimmicky and it actually counters the initial concept of randomness in the number of moves for each tile (because after playing a lot you begin to see patterns for the tiles and can predict them).So I wanted...

Through holes will be automatically +1/32in and tapped holes will automatically be -1/32inScrew length - Use exact length of screw so that there is no protrusionArm Thickness - SET TO DIAMETER OF YOUR SPRING since you need to fit the spring in...

Details are on but will need supports and will likely be very fragile.Print separately:borealis_keelborealis_iceterrainPost-PrintingIce TerrainPrinting out the terrain with white filament works well enough, but I've attempted an interesting technique...

It's a bit thicker (+1mm) to allow you to screw the steel plate on to the Probe Distancer. Use short screws so they don't touch your 4010 fan. * PTFE tube length to cut: total 34mm (have tube sticking 6mm out of the Groove Mount Adapter) Never...

==================================================================== I may still look at improving this design as I feel there must be a way to have the switch lock into place with a little bit more resistance, but for now this works fine. takes...

If for some reason it's loose (maybe you bought the wrong thickness plastic strips or your printer underextrudes) you can put some scotch tape on the end of the plastic to make it a bit thicker. 2. Secure the bottom of the long strips of plastic to...

You then should have enough space in the middle of the belt to push in a 15 to 20mm piece of filament to lock the belt. Yes, it looks a bit strange, but trust me, this holds a lot of weight. I wondered why no one ever came up with this idea. .)...

I also found that applying a thin layer of petrolium jelly with a cue tip to the inside of the ball race made the BBs stick a bit and less likely to fall out. Next insert the Outer onto the mounted Lower Bearing Outer. No glue is required. Repeat the...

Due to the very slow curve of the part, the supports are a bit tight fitting but do the job well. The supports have only been tested using .2mm layers but 'should' work with smaller layer heights. The supports come off in four parts. Do not use a...

The holes in the case / housing may need to be eased with a suitable drill bit - 4mm on one half of the case and 3.3mm (for tapping to M4) on the other.You need to print 2 cases, 1 rotator, 1 bearing, 1 lever bearing and 1 lever for each gate, and...

----Update---- 20/01/2023 - Edge TrimsI've added some optional edge trims to cover up the edges a bit. Print 4 edge trims for the vertical edges and one top trim for the top. The top trim features 4 arrows that denote where the chosen symbol should...

even when I don't ever try to choose colors in any way, this time the rendered pic looks a bit Spanish heheh... UPDATE (07-JUL-2016): Noticed that a quick solution is possible making an adapter to avoid dismantling the CoreXY system to install the...

(I'm far too pleased with this little bit of upcycling than is reasonably warranted …) Hang from Christmas Tree or Festivus pole.Alternative Material:  I also used a stainless steel mesh (pictured below left). It didn't turn out as well. A...

The nuc with spout may hold a little bit more. If you wish to use a piece of Plexiglass over the frames under the lid, a piece of 3/16" or 5mm thick, 143mm x 132mm, will fit over the frames. I have also included an SVG for laser cutting the...

**Building the model** Colors (your colors may vary, as this character has changed quite a bit over the years) Black: (Paramount3D PLA - Black) eye_black_right eye_black_left eyebrow_right eyebrow_left nose .. Dark Red: (Paramount3D PLA - Iron...

The only reason not to use CV2 is if you do not have any flexible filament, CV1 will work for you in that case. With CV2 you can seemlessly switch connectors that are in use, for example allowing you to block passages between modules by switching out...

Place a few dabs of hot glue on the flat side of the magnet mount, and then attach it to the central hub of the fan (the bit that rotates with the fan). Attach a 3.5 mm male plug to the multi-voltage power supply and plug it in. Hot glue all the...

Don't be surprised if you need to re-tighten it after a few days because the rubber plug will change shape a bit, but it shouldn't fall out. I had to tighten mine slightly twice in about 3000 miles, but since then I have replaced the intake tube...

The caliper-stop, is a bit loose, and maybe needs to be resize 99.9X% to be tight enough for proper friction-fit. The caliper-slide is near perfect for sliding, maybe 99.99% resize. The eraser-plug, maybe 100.4% for snug-fit. Maybe the...

Motor position can be adjusted, so there's some leeway in choosing the belt length (I use 1220mm) the bottom parts that hold the 40t pulleys is in two parts for easier printing there's optional support parts for eliminating the bending on the middle...

In my 4 months of using it non-stop it has never come loose or moved, the force needed to take it off the rail is a bit more than the force needed to make the motor skip steps so something would have to go CATASTROFICALLY wrong to make the tool...

This was a fun design process, and it is a bit of a challenge to print. It took me a few goes to get it right.It's my first attempt and I've included the Fusion 360 file. You'll notice that the head and body are in two separate parts. I did this...

This sign is totally optional, and you can always make something yourself and glue a bit of slot-cover to the back to clip it in place. I've included a cut list for the extrusions, a parts list for the hardware, and a parts list for the printed...

The tray bit was mostly flat on the top layer, but had a random spot where it wasn't near the hole. Didn't show up on 100% scaling, but absolutely did on 125% scaling, where the topmost shell wasn't a fully flat surface, but had line gaps to work...

The rounded version adds a .6mm rounded edge at the bottom layer for smoother meshing between pieces.\r\n\r\n---------------------\r\n\r\nUpdated version 2.2 - 2/14/19\r\nI've made a couple of very minor adjustments, making some of the layers smaller...

The new part deviates a bit more from the original N64 shape but since it's on the bottom maybe it's not a big deal. If you choose to use the alternate case bottom you'll have to print 2 of the front and aft feet each then glue them onto the...

1x 450mm Linear Rails with MGN12H Bearing - HERE This project is still a bit of a work in progress. I need people to test the parts and make any recommendations on improvements they may have. I'll continue to update this as much as I can. ...