monstercat 3d model

 The fan mounting holes are sized to accommodate a Brass Heat-set insert size M3x4mm.  The holes are not threaded and too large to accommodate an M3 screw itself.   Upgrading the Raise3d Pro2 with a Copperhead  Note: Both Hotends must be replaced...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.3...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 180...

Some models that may be compatible: BOSCH, SIEMENS, BALAY SGV09S03/28, SHV99A13UC/19, SGU4670/04, SGI6600GB/07, SGS4432II/01, SGS4952EP/22, SGS43A62EU/01, B1EIN1601B01, B1ESN1601B01, B1STA4319B12,B1STA4319R12, SGS43E22EU/20, SGS56A92EU/35,...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

They are both definitely WIP, I do not own a Orbiter V2 and are based on the CAD models. Update:18\10\21 Uploaded some 5010 fan ducts which are 8.5mm longer to allow for a Volcano Hot End. These are definitely WIP. I have not printed, installed or...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

When/if I model it, I will put it on here.Have any modification requests? Contact me in the comments. I am active on Thingiverse.If you want to modify the design yourself, I can try to provide the original Tinkercad schematic on request.Update: Added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

Print Settings: - Printer Brand: MakerBot - Printer Model: MakerBot Replicator 2X - Rafts: No - Supports: Yes Important Print Note: The key thing to keep in mind when printing these wheels is to use support material, especially for filling in the...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

For any other question, please feel free to reach out, or leave a comment. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Filament: Jarees PETG Matte Black Notes: Support is only...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance = 0.4...

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

... The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

3 perimeters 7 bottom layers on the cap ( definitely overkill ) 4 top layers Gyroid fill pattern ( any pattern will do ) Extra perimeters if needed was checked Seam position Rear ( make sure the hinge potion of the model is pointing towards the back...

If you're experiencing high stringing, do not worry, give it a blast with a heat gun, then a quick brush with a nylon brush and wipe down with a cloth to get rid of any remaining strings. Exterior Perimeters settingsTo ensure the best results...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

At each joint- extend the cable to it's most strained position and then firmly secure it to the next joint in the chain with a zip tie. Example Setup:Though I tested all of my parts and you can assemble in any configuration you like, if you want...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 0 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

Printer Settings: * Printer Brand: MakerGear * Printer Model: M2 * Rafts: Doesn't Matter * Supports: Yes * Resolution: 0.4 mm nozzle * Infill: 30 - 60% * Notes: This is a very big object, taking a lot of plastic (~1/3 - 1/4 of a 1kg roll) and many...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...