monoprice select mini v2 3d models

I designed a custom LED strip light holder specifically for my Maker Select v2. To ensure clearance for my frictionless spool holder and filament guide, I utilized an 8mm offset for the upper mounts. ...For the sides, I opted for a 4mm offset to achieve...

This protective covering for wires was created to safeguard cables over the extruder when the maker selects reach their maximum Z axis height, a full 178 millimeters above ground level. ...Its design draws heavily from the ingenious Wanhao Duplicator i3...

As most owners of the Maker Select V2 have probably realized, the standard spool holder often proves too flimsy for larger filament rolls. This innovative design effectively lengthens the existing holder by approximately 2cm, providing ample space to...

Attach a versatile clip designed specifically for the Monoprice Mini Delta to securely hold the Raspberry Pi Camera v2 Universal Mount in place.

The Maker Select v2 LCD board allows you to mount it on the bottom right side of the Maker Select frame or have it sit freely on a desktop. **Assembly** Mount the face plate to the LCD board and attach the base to the MS frame using 2 or 4 M3...

This is an enclosure for the Maker Select V2 crafted from a budget-friendly bedside table and desk. The control box still needs to be mounted underneath the desk, but I have to design some sturdy support brackets first. Up top, I drilled a 1-inch...

Hold a glue gun, every tool included with your manufacturer's kit, select version 2, and a complete set of gauges.

... is more than welcome! ...I created this as a remix of https://www.thingiverse.com/thing:1718783\r\n\r\nIt snaps securely onto the side of my Maker Select, storing my Allen Hex Keys, Scraper, Wire snips, Drill bit, and MicroSD Card with precision.

This is a modification of the bottom brackets found in http://www.thingiverse.com/thing:1685857. My version of the Duplicator has three bolts on the lower end, but the 3D model only had two bolt holes. To achieve support at all four corners, print...

This is a reinterpretation of an incredible design courtesy of berky93 on Thingiverse. I flipped the piece to create a matching left side and lengthened the standoff to accommodate a standard roll of tape with ease. As this is my first remix, I'm...

The ultimate solution - an 80mm fan duct engineered to bring even the most high-speed PLA printing to a screeching halt. ...Its sole purpose is to put an abrupt end to rapid-fire production, rendering any printer completely useless for swift and...

I needed a non-enclosed Pi mount that utilized hardware of my preference and featured a camera attachment swivel mechanism. Additionally, I wanted to be able to integrate an extra mount for something like a LED component. To achieve this, I created...

I recently bought a glass bed and installed an inductive bed sensor, but got tired of the binder clips and wanted to try something different. Sooooo, I designed this little bed corner. It uses the screws from the underside of the heated printbed to...

Bed level is a huge issue, and it's largely influenced by how things are aligned. Let's face reality here: most 3D printers are slapped together at the factory without much care for precision. So, getting everything perfectly straight is what we need...

I modified uwe999's MOSFET mount to be shorter by attaching it to the two standoffs closest to the LCD screen. I used spare PC bracket screws to secure the MOSFET to the printed bracket. The dimensions are 7.05 cm by 10.92cm with a height of 0.8 cm.

This Episode based on https://www.thingiverse.com/thing:2754973. Today we upgrade the X-Axis by adding a 30mm Spacer without purchasing new parts. To achieve this, remove the X-Axis Linear Bearing and shift the inner Rod Holder to the outer...

Remixed from the original design and extended the case to have a mount on the controller .

After installing the Z extensions thing: 2588219 I wanted to make use of the additional space so I threw together a lightbar. This is hard wired directly to the 12V end of the power supply so it turns on when the printer is turned on. I used a...

I wanted to increase the setup repeatability of my printer and the easiest way to do this is to add a BLTouch or similar sensor to allow the use of mesh bed leveling. This is a remix/redesign of thing: 3635758 with my LED light bar thing: 2640410...

I mad this wheel to guide filament if the spool is set up on the control box instead of on top.

I designed this custom remix for the MOSFET with 60.5x26mm (12/24V) hole spacing. To provide extra stability, I installed a support bar connecting the mounting holes on the Melzi board due to its flexible nature. ...The Melzi board support is also...

... prints in under 40 minutes and keeps everything neat! Simply snap it onto one of the pillars and adjust the height to your liking.  Print Settings:Resolution: .2mmSupports: NoRafts: NoWall line count: 2Infill: 15% Printed on: Monoprice Mini Delta v2

This is a precise replica of the Monoprice Mini Delta.

MonoPrice Mini DeltaHousing to mount Igus drylin Bushings

This is a set of parts for helping design a 3D printable pen holder to be mounted inside a Monoprice Mini Delta v1. ... Hoping to get it to work with Andrew Sink's sweet pltr v2 - Pen Plotter Toolhead system...

Mount a webcam on the Monoprice Select Mini using its versatile Modular Mounting System.

This is a set of parts for helping design a 3D printable pen holder to be mounted inside a Monoprice Mini Delta v1. ... Hoping to get it to work with Andrew Sink's sweet pltr v2 - Pen Plotter Toolhead system...

This is Version Two, boasting an even narrower divide.