monoprice select mini v2 3d models

Here are the print settings I used: Printer: MP Select Mini Rafts: No rafts at all Supports: None needed Resolution: 0.175 mm for a smooth finish Infill: 30% to give it some structure and density Notes: It printed out great in PETG, and the result...

MonoPrice Maker Select V2, also known as Wanhao Duplicator i3 V2 printers, have an issue where a cable can get caught on the back of the frame. This print clips onto the frame and forces the cable upwards, so it can't catch on the side of the...

This is available here: https://www.thingiverse.com/thing:4652745 This is a slim new design, tested on V2. Flush with the bed, compatible with any part cooling hacks. No Z-height offset. But if you need any offset (ex: glass bed)...

This is available here: https://www.thingiverse.com/thing:4652745 -------- This is a slim new design, tested on V2. Flush with the bed, compatible with any part cooling hacks. No Z-height offset. But if you need any offset (ex: glass bed)...

I recently purchased this Mk8 extruder for my Mini v2, a printer known to thrive with Creality-recommended parts. This Mk8 extruder is touted as an upgrade for printing flexibles and I decided to give it a try despite its intended purpose. When I...

This system is compatible with Lanmu's SD card extender, which can be purchased on Amazon at the following link:...

The slight play in the unsupported arm of the Select Mini began to reveal its limitations, resulting in layer issues. It was time to build a sturdy X axis support gantry. The only hitch was that all of the good designs were tailored for 6mm...

I quickly combine the mount with MKS_TFT_3.2_v2.0 mount from here in meshmixer : https://www.thingiverse.com/thing:2317518

Screws: original SD card extender:...

Clips for securing a glass bed on the Monoprice Maker Select V2 are available here, and they may also work on the Wanhao i3 v2, but I don't have one to test them on. Note that my glass bed is exactly 200mm x 213mm. Since it's only 8.5mm tall, I was...

The mounting holes have been carefully tested to ensure a perfect fit with the Monoprice Maker Select V2 3D printer that I happen to own. The mount takes advantage of two screw holes located at the top of the printer, which are then reused to install...

This longer spool holder replaces the one shipped with the Monoprice Maker Select 3D Printer v2, allowing you to use larger spools that won't fit on the factory holder. Printing Recommendations: Print a raft bed for best results. You can also print...

A Simple Switch Mount for the Monoprice Maker Select v2. Designed with Versatility in Mind. Mounts seamlessly to the bottom of the printer's frame on the left side, allowing easy access and precise placement. This switch mount utilizes two m3x8...

This is a custom camera mount designed specifically for the Microsoft LifeCam NX-3000, allowing it to be seamlessly integrated onto a Monoprice Maker Select 3D printer or other printers sharing a similar build and design.

I made some minor adjustments to cantizzy's spool holder design: Expanded it slightly to accommodate 1kg spools from Monoprice Shortened the length by about 2cm since I don't use spools that need this extra height Improved the attachment points on...

A swift tweak to an already outstanding design, simplifying the center hole's depth to ensure the button shaft on the Mp Mini V1 clicks with precision across various models - notably addressing a recurring issue where excessively lengthy center holes...

... No raft or support structures were utilized. Resolution and Detailing: A resolution of 0.175 millimeters was selected for precise printing. ...Internal Filling Patterns: 20% grid infill patterns were chosen to optimize structural integrity.

Here is the first version I designed for the M320: https://www.thingiverse.com/thing:4720138 Needed to revisit the design for my Mini/M200. There it is! Compatible with all spools (ID >50mm and wide as 85mm). The spool roller requires support at...

Here is the first version I designed for the M320: https://www.thingiverse.com/thing:4720138 Needed to revisit the design for my Mini/M200. There it is! Compatible with all spools (ID >50mm and wide as 85mm). The spool roller requires support...

I created this attachment specifically for the Monoprice MP Select 40mm Fan Duct Shroud V2, which can be found on Thingiverse at https://www.thingiverse.com/thing:2166473. This attachment sits about 1mm off the bed and blows wide in both X and Y...

Filament Guide - Wanhao i3 / Monoprice Maker Select v2Based on another guide posted by KIWI-3D.Changes:1) Sides curved2) Mounting plate extended beneath filament spool holderSTEP file included in case you want to make changesIt might help to get (2)...

The Monoprice Maker Select V2 is essentially a rebranded Wanhao Duplicator 3, but it's not a bad printer for the price considering current options. I purchased this printer a long time ago as my first one. Unfortunately, they have a poor print...

Light Bracket - Wanhao i3 / Monoprice Maker Select v2I used with a USB Light from Amazon. ... Extended to clear filament guide.DWEPTU Under Cabinet Lighting Dimmable Under 12 Inch Cabinet Lights with USB Powered for Closet Light Bar Under Counter...

The human edition is tailored specifically to meet the requirements of the Monoprive Maker Select V2. ...This version has been carefully crafted to ensure seamless operation and optimal performance with this particular model.

The new design of the MP Select V2 features an updated card slot that necessitates adjustments for seamless functionality. ...To accommodate this change, I made modifications to ensure smooth operation.

... http://www.thingiverse.com/thing:193948 which offers a clever and more streamlined solution. Print Settings Printer: Monoprice V2 Rafts: No Supports: No Resolution: 0.15 mm Infill: 100% How I Designed This I edited RotoScan's stl files in TinkerCAD

The Monoprice Maker Select V2 is a rebranded Wanhao Duplicator 3 and they are not terrible printers for the price although nowadays there are much better choices. It was the first printer I bought quite a while ago. However, they share a TERRIBLE...

I had some liquid rubber I used to coat the tip of the screw just in case (not reflected in picture) +Placing this between the heated bed and the locknut should satisfy the safety concerns with Wanhao's recall (Monoprice Maker Select is the same...

... branding on the cover plate, adding a small nameplate for personalization. ...The base file remains unchanged, but I've included it here to simplify access for those using the Monoprice clone, allowing us to accessorize with style and consistency.

This bracket was designed to work with the RepRap Champion Y Carriage Plate Upgrade for the Monoprice Maker Select / Wanhao Duplicator i3. To install this upgrade: Place the bracket between the Y-carriage plate and the hot bed, making sure the...