monoprice mini select v2 3d models

This remix is built from [keco185's Monoprice MP Select Mini V2 40mm Fan Shroud](https://www.thingiverse.com/thing:2448223) and [pointfiftytracer's 40mm fan booster](https://www.thingiverse.com/thing:2347716). **keco185's description of the...

The fan duct is designed for use with the Monoprice Select mini V2. It utilizes the MPSM's original 30mm fan as the part cooling fan, and a single 30mm fan as the hotend cooling fan, powered by a 12v power supply. Alternatively, the power wires...

... hitting a switch 90 degrees from the part. I just used the dial as is. Print Settings Printer Brand: Monoprice Printer: Select Mini Rafts: Yes Supports: Yes Resolution: 0.13125 Infill: 33 Filament: Monoprice ABS+ Yellow Category: 3D Printer Parts

I love my Monoprice Select Mini v2 3D printer but I made up my mind that having a front power switch and some 5V USB sockets to run lights and fans off would make it even better. So I designed this power console which also includes a cheap 30V...

I love my Monoprice Select Mini v2 3D printer but I decided that having a front power switch and some 5V USB sockets to run lights and fans off would make it even better. So I designed this power console which also includes a cheap 30V...

* I've added support to the top blower screw mount so that it no longer needs support to print, it is touching the build plate * The screw holes have been adjusted to fit M2 bolts, since that's what's standard on the Mini Select V2 and I had a bunch...

A decorative accent panel for the Mini v2, carefully crafted for precision and beauty. This design is specifically intended for laser cutting, its intricate details and shapes best brought out by this method. If you have access to a large enough 3D...

I adjusted my Mini v2's endstop as it was too tall, but the opening on the Z-axis for the X-axis arm wasn't low enough like the v1. So, I created an internal endstop mount that attaches to the bottom of the Z-axis rods. The spacer is separate; you...

Printing with TPE on my Mini Select was a challenge - lots of glue stick, slow speeds, and patience were required to get usable ones. Inspired by other designs, I used two things as references: https://www.thingiverse.com/thing:2722203 and...

... the power supply that's mounted below the black extruder arm. It works perfectly! Ensure your LED strip is under 3mm in height to avoid hitting prints. This setup should enhance someone's experience with their mini and bring a smile to their face.

... (from the power supply) that is mounted below the black extruder arm. Works great! Make sure your LED strip is sub 3mm in height, so it doesn't hit the prints ;) Hopefully this will help someone / will make someone enjoy their mini a bit more :)

I have a v2, so it stands to reason the screw locations may have varied. It works for me and may be a good starting point for you, but be prepared to tweak the bearing mount to suit your needs. I swiped the 6mm linear rail cap from Mdkendall's...

I replaced the Melzi board on my Monoprice Maker Select v2.1 with an Ultimachine Mini Rambo, and it fitted snugly despite some initial concerns. ...So far, everything has run smoothly, and I'm hopeful that this upgrade will benefit others as well.

Remix of m_power design : https://www.thingiverse.com/thing:2719472 Simply made it straight so that it does not get damaged on the closet wall when I store it. ... I have added a blend file for easier remix.

I attempted printing the Zero Offset mount for my MPSM but encountered an issue with the holes for the heat sink clamp being too small, making it impossible for either the stock V5 clone heatsink or the genuine V6 heatsink to fit. I modified the STL...

Includes 2x SD card slots, 6x microSD card slots, hole for the stock allen key, and a small hook to hang whatever you like (in my case, my SD card reader). Screws into the top of the printer with the two screws holding the rear panel. ...The SD card...

This mod ensures that stepper drivers don't shut down due to overheating issues. If you notice a ticking noise coming from the extruder, it may be caused by an overheated driver. When a driver overheats, it faults and cuts off power. ...The pressure...

Design a system that maximizes airflow by leaving the majority of the fan's pulling section exposed. ... The cover integrates seamlessly with the standard mounting hardware.

Air Flow Maximization through Simple Design. This Cover Integrates Seamlessly with Standard Screws. ... Explore My Range of Fan Covers, Tailored to Your Needs.

I added some filleted edges in Tinkercad to strengthen the model.

I inserted a glass plate into my 3D printer, prompting me to devise a means to precisely position the glass on the print bed. ...Consequently, I engineered four custom clips that securely fasten to each corner of the glass plate.

This model was crafted using Tinkercad's intuitive design platform. Make adjustments online at https://www.tinkercad.com/things/9DOuLzIycVW. ...To achieve optimal results in slicer settings, set the Y-axis to 4mm for precise scaling.

I mounted a glass plate onto my 3D printer, necessitating a solution to accurately position the glass on the print bed. ...Therefore, I created these clips that securely hold each corner in place.

Rails must cut to the same length as the rods. ... 2X Linear Rail MGN9H 200mm: https://www.aliexpress.com/item/32899254961.html?spm=a2g0s.9042311.0.0.54524c4daARiA3 12x M4x6 insert...

Modified the original design at https://www.thingiverse.com/thing:2169902 to make it compatible with a Zmodo camera. Note that you'll need to print three specific components from the original thing first: the Camera Mount, Camera Straight Mount...

I'm diving into 3D printing and CAD software, so bear with me. I was experimenting and came across a Sue T-Rex head model uploaded by another user - you can find it in the source file. Next, I stumbled upon a feeder attachment just for kicks, which...

This part takes the place of the rear section of a standard dial gauge and securely clicks onto the z-axis rods.

I've found the original fan mount clips a real nuisance and any attempt to fiddle with the hot end is a major pain. I desperately needed a way to quickly remove the part cooler and adjust for different height tips, which was largely driven by my...

I printed it in PLA, however, i would recommend using some heat resistant filament.Print with tree supports, they are easier to get out.According to the datasheet, the stock MOSFET (A29T) can also handle the current, that the new fan will consume,...

This object was created using the 3D modeling software, Tinkercad. ...You can edit it right now by visiting this website: https://www.tinkercad.com/things/9DOuLzIycVW This is actually my latest design iteration.