monoprice mini delta fan upgrade 3d models

USED ELECTRONICS, ARDUINO MEGA AND RAMPS 1.4 IN ADDITION TO THE UPGRADE A LAYER FAN WAS IMPLEMENTED, EXQUISITE DESIGN WITHOUT SACRIFICING SPACE OR THE IMAGE OF THE HOTEND, USING THE SAME COMPONENTS. THE RESULTS AFTER THE UPGRADE ARE EVIDENT. THE...

This custom design replaces the original hotend fan shroud on the Monoprice Mini Delta. It's not an exact duplicate, but it's remarkably similar. I intentionally left a bit more space for the heater cartridge, which I had previously damaged when...

A simple mounting bracket for a cooling fan fits perfectly with the Monoprice Mini Delta's design. A parametric CAD model is used, already set to accommodate a standard 120mm fan that suits this particular printer. To assemble it, print four parts...

... For sure, this happens on every Monoprice Select Mini, so I designed these modifications to fix both problems. Apart from those issues, I hate the way the part is attached to the printer, so I also designed some snaps to make it easier to install.

Adapter for the Monoprice Mini Delta 4020 Blower Fan Assembly - Requires One M3 Screw and Nut.

These brackets for fans are used to attach a 120mm fan to the Monoprice Mini Delta printer. The original idea for this bracket was posted by nrp, but his version did not work with either of my two 120mm fans. Two new brackets were designed that fit...

So I lost the metal clips for the fan mount of my Monoprice Mini Delta printer and I checked to see if anyone had actually made a replacement clip, but it seems like they haven't, so I designed these myself as a temporary fix, and while they're not...

Upgrade your MonoPrice Mini's Hot End Fan Duct with this easy installation that lets you mount a 40mm fan, providing superior cooling for enhanced performance and reliability.

Upgrading your MonoPrice Mini's Hot End Fan Duct is a simple way to boost cooling performance. ...This modification enables you to mount a 40mm fan, providing improved airflow and reduced thermal stress on delicate components.

I replaced the stock Mini Delta fan with a cheap generic 12v 120mm fan because it's extremely loud. The printer is now completely silent when idle, making it much more enjoyable to use. To install this new fan, you'll need to add the appropriate...

To accommodate this upgrade, you'll need to use a larger printer or order a print from somewhere else. The model's dimensions are slightly bigger than the MPMD's print volume. It measures 214mm x 145mm x 15mm in size. Three M4 threaded screws fit...

Changes: - Optimized Fan Design directs airflow directly from heat-sink to part cooling - Enhanced intake maximizes fan performance - Removed redundant part cooling fan - Restricted part cooling exhaust allows for larger heating block installation -...

To reach the fan connector you need to unscrew the two screws on the top side of the display panel (you should already have removed the bottom ones), then you should be able to pull it out a little bit, unplug the power cable next to the fan...

Springy Fan bracket for MPMD V2. I bought new fans (Sunon MF40101V2-1000U-A99 for inside and MF30101v2-1000U-A99 for hot end) for my MPMD v2 but the internal one was still making a lot of noise, figured out it was making the plate it was mounted to...

This upgrade replaces the factory duct on the monoprice select mini while also upgrading to 40mm fan (from 30mm). Printed fan mount flange down with support when >50 degree angle. Take caution when removing supports from the side spring clip mounts...

Remixed to fit my Monoprice Select Mini V2. Supports for the side-nubs are embedded in the model, you can either keep them or clip them off. ...The clips can hook around either way.

I designed this fan shroud to be able to upgrade the stock blowers. There are a couple height extensions to allow clearance for after market hotends. You will need to buy a fan: https://amzn.to/3c2F9Yt spade connector: https://amzn.to/3wDl2tc  ...

This is an accessory for a Monoprice Mini Delta. ...It improves air circulation underneath the printer, and it also reduces the noise level produced by the fan.

Stock linear bearing replacement for Monoprice Mini Delta Printer. ...This is a hot-press fit component, requiring removal of the rod from the printer before applying heat with a heat gun or stove to reach 120-150C, then pressing the bearing onto the...

Attachments for stacking Monoprice Mini Delta printers vertically include feet that must be installed at the top and bottom, utilizing existing screws on the printer. Secure the top printer with M3 screws and nuts, then attach the next one below it...

... at the bottom and mount a 120mm fan between three of these supports. Update: I got some feedback that my angles were off, and I forgot to include screw holes. There are several better legs available on the Facebook MP Mini Delta Owners group.

This is a straightforward modification for the mini delta that employs magnets for easy installation (6x3mm). I'm thoroughly impressed with the quality of my prints from this printer, so there was no need to upgrade with additional components (if it...

Print 3 for the set of Simple Legs. ...Install them on your MP Delta Mini printer to elevate it, improving airflow and overall performance.

The miniature fan located at the base of the MonoPrice Mini Delta is a welcome addition since its initial production batch, effectively keeping the electronics cool with its assistance. However, due to its placement on the bottom, it will be more...

A smaller version of the mini delta hotend fan cover that doesn't interfere with the bed clips during the leveling process (G29) - at least in my case. Requires two magnets: 4mm in diameter and 2mm thick. ... I use it for PETG prints, but I've never...

I wanted to make an enclosure for my delta, and had some free acrylic to work with. I designed this and printed a total of 6, two for each space. The sides rest in the slot allowing the 8mm thick acrylic to slide either way, and be removed easily. I...

My build uses the following additional parts: 12V LED PSU like this one here: https://www.amazon.de/gp/product/B01LWZ3MI4/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 PSU Plug like this one:...

My build uses the following additional parts: - 12V LED PSU like this one here: https://www.amazon.de/gp/product/B01LWZ3MI4/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 - PSU Plug like this one:...

... <p class="detail-caption"><strong>TPU feet like in the original design. The Switch here was added after printing. The hole had to be drilled used prusa slicer to create a grill for the base fan final build Category: 3D Printing

Decided to upgrade the hot-end fan of my Monoprice Select Mini V2. Unfortunately, the Noctua NF-A4x10 PWM I ordered needed a capacitor to get it going, otherwise it would if the hot-end climbed higher than 70C; an online search revealed I need to...