monoprice maker ultimate upgrades 3d models

Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: PCBLength is set at 70 The width is set to 90 FootHole...

I specifically wanted a dual-color Z-brace mod for my Monoprice Maker Select, so I used Azza's original file and duplicated the "balls" to achieve my desired effect. ... The "balls" can also be utilized for the "Plus" versions of these printers, leaving...

The initial blueprint exhibited several mesh inconsistencies that precluded its functionality within Simplify3D. However, since Cura disregards these inaccuracies, we didn't encounter any issues with the program during testing. ...To rectify this issue,...

... For sure, this happens on every Monoprice Select Mini, so I designed these modifications to fix both problems. Apart from those issues, I hate the way the part is attached to the printer, so I also designed some snaps to make it easier to install.

... rubber foot. Print Settings: Printer: Monoprice Maker Select Rafts: None Supports: None Resolution: .20mm Infill: 30% Notes: Since this part doesn't require the same strength as the main components from the Azza mod, I used 30% infill.

For: Monoprice maker select V2, Wanhao duplicator i3 and other clones with the same spool holder. I crafted this spool holder extension to be a straightforward solution to accommodate larger spools of filament that won't fit on standard holders. I...

Control box disassembly video: https://www.youtube.com/watch?v=bXQ1gAid17Y Print Settings: * Printer: Monoprice Maker Select * Rafts: No * Supports: No * Resolution: 0.2mm * Infill: 100% * Notes: Don't forget to rotate the standoff to fit on the...

This series will kick off a development of my Wanhao Duplicator i3 v2.1. This episode will push the X-Axis holding frame both 30mm wider and the bridge 30mm higher to allow further advancements. Azza's Z-Brace will be supported throughout this...

MOSFET wiring info: http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/di3-advanced-mods/heatbed-terminal-burning-fix-with-mosfet-board/ Print Settings Printer: Maker Select v2.1 Rafts: NoSupports: No Resolution: 0.2Infill: 50% Category: 3D Printer...

... mounting options, I've designed the extruder bracket with multiple hole pairs. I'm using two short M3 screws to secure the mount to the X-end's cable chain holes, relocating the chains to the top of the new printed mount for a seamless upgrade.

I remixed it because 8mm is taller than the stock standoffs on the maker select v2.1 control box, which are only 6.8mm, 7mm at their closest and 7.34mm at their farthest points. An 8mm part would cause the control board to rise up onto the printed...

... to use the full bed in the Y direction. For the belt tensioner, check out this design on Thingiverse (https://www.thingiverse.com/thing:1784375). I've since upgraded my setup with a custom nozzle fan design and a 50mm x 15mm blower fan mount.

I needed a more reliable base for my Logitech 910. The remarkable CMH mount served me well for quite some time. This mount attaches to the exposed door hinge pins on the printer. Not using ABS, I don't require an enclosure. The hinge is engineered...

I created a simple remix of mentalbobs mount by adding a mount for the stock 40mm fan, allowing it to be moved closer to the motherboard. I recently acquired a 60mm fan and tried installing it with the new 40mm bracket, but unfortunately, it...

<p>These are 21.25mm brackets to offset the servos to the correct distance with dampers in place and to get some additional dampening. Used 3D Printer Motor &amp; Vibration Dampers that are 5.75mm in height. The long version has additional lugs on...

Moving the filament sensor to the top of the print head is crucial now that I'm feeding filament from above the printer (thing:2789243). Keeping the PTFE tube attached helps nicely manage cables. For more information on filament run out sensors,...

This is yet another filament spool holder for the Wanhao D6 with bearings. This will hold standard 1KG spools and 3.5 KG spools that measure 12" x 4". The designs I tried didn't work with my cheap 608 bearings as putting pressure from only one side...

I was thrilled to discover some filaments that were so coarse they wouldn't be pulled smoothly through the filament sensor and PTFE tube to the extruder from behind, especially with Fluorescent PLA and wood filaments. I repurposed existing designs to...

<p>Needed to move the filament sensor to the top of the print head as I now feed the filament from above the printer (thing:2789243). I keep the PTFE tube attached as it nicely holds up the cables. Filament run out sensor details can be found here:...

I finally came across some filaments that were so rough that they weren't pulled efficiently through the filament sensor and the PTFE tube to the extruder from the back (Fluorescent PLA and wood filaments). Re-purposed some designs to create this...

These are 21.25mm brackets designed to precisely offset the servos with dampers in place, providing additional dampening for a smoother experience. Utilizing 3D Printer Motor & Vibration Dampers that stand at 5.75mm in height, these brackets have...

I was finally able to track down some filaments that were so coarse they couldn't be pulled efficiently through the filament sensor and PTFE tube to the extruder from behind, especially with Fluorescent PLA and wood filaments. I repurposed existing...

Universal Camera Mount for Wanhao D6 with Quick Release A versatile mount designed to quickly secure your camera in place, allowing for effortless access to the print area without requiring removal of the entire mount. This innovative design features...

This is yet another custom filament spool holder designed specifically for the Wanhao D6 with bearings. It securely holds standard 1KG spools and larger 3.5 KG spools measuring 12" x 4". My previous attempts at creating a spool holder failed due to...

<p>This is yet another filament spool holder for the Wanhao D6 with bearings. This will hold standard 1KG spools and 3.5 KG spools that measure 12" x 4". The designs I tried didn't work with my cheap 608 bearings as putting pressure from only one...