monoprice maker ultimate upgrades 3d models

I reengineered this mount on Onshape based on Badvision's remix, flipping it upside down with a wedge carved out near the stock cooling fan so it doesn't nestle too closely to the hotend while still fitting snugly between the hotend fan and the...

I've collected all of the components from both the parent project and the grandparent project. The parent project lacked the top braces and ball nuts, while two STLs were distorted - the front right was miniaturized and the back right didn't render...

The widest spools I have come across were 90 mm so I made this one with over 91 mm of usable shaft. For the shaft, print with the threads at the top. The nut should be with the flat side down. ... Your stock nut will also work with these threads as...

I needed a hook for the scraper tool that comes with this printer. So this was born. ...Hooks on the top and hangs down the side (see pic).

Increased Z Axis Mod Boosted Z axis height to a whopping 260mm Extra Required Materials: 2 x 400mm Dia 8mm T8 Lead Screw and Brass Nut 2 x 406mm Case Hardened Chrome Linear Motion Rods/Shafts/Guides, each measuring 8mm in diameter 4 x M3 8mm Hex...

Simple Mounting Bracket for LED Lights Around Printer. ...The lights featured in this setup can be found at Amazon, listed under the product code B077B292R7.

A convenient clip-in adapter that allows easy passage of the filament without snagging as the material runs out.

Just a camera mount to get a good angle of the bed. ...There is an extended mount and a straight mount for different angles.

The human requires two duplicate spool holders, each equipped with a sturdy three-quarter-inch PVC pipe.

I fashioned these hasty little supports to affix to the base of my printer after switching to a glass-topped desk. They're designed to accommodate common 33mm adhesive felt pads readily available at most department stores. The resolution and infill...

I WILL PRINT IT WHEN MY CURRENT JOB IS COMPLETE! YOU WON'T HAVE TO WORRY ABOUT HITTING THE BACK BUTTON OR STOPPING THE PRINT MID-STREAM AGAIN. THIS LITTLE GUARD CLIPS ONTO YOUR DESK AND SLIDES UNDERNEATH YOUR 3D PRINTER, KEEPING THOSE ACCIDENTAL...

I had made up my mind to suspend the scraper from its hook.

Part used to give a little extra support to the gantry frame.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Smaller diameter curved top than the original, with a through-hole for the key for ease of printing. Printed square stock down, rounded side up(with the hole vertical, so it doesn't require supports). Just like the original, flip the spool holder...

Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Vent = 50 Text =...

Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Arial Black font for Police sign Resolution set to 50...

Using the following options: Height is set to 50 Vent is turned off BPanel is activated Foot diameter is 8 m is 0.9 txt is Frequentieteller PCB width is 80 Length is 90 TShell is on Police font is Arial Black FPanel is activated BShell...

Human: Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Resolution is set to 40 dpi. The...

Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: txt = Font = Arial Black Text Color = Black Width =...

Customized version of Thingiverse - 1264391 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Using the following settings: Text Size: 3 Front Panel Thickness: 1 Roundness: 2.1 Base Shell Thickness: 1 ...

Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following settings: TxtSize = 10 Text = 1 FPanel = 1 Round = 3.1 Width =...

Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Text = 1 BPanel = 1 txt = HeartyGFX Police = Arial...