monoprice maker select v2 glass bed 3d models

After designing and building the Z-brace mod for the Monoprice Maker Select Plus, as described on https://www.thingiverse.com/thing:2349318, it became clear that side feet adapters were necessary for the column braces, since the original design only...

The Monoprice Maker Select has a tendency to misalign its Z Axis motors, creating the appearance that the build platform needs calibration. This issue arises when you turn off the printer and the motors release at different rates, according to...

Add a Raspberry Pi 2 or 3 plus power supply and SD card to create an entire Astroprint setup with a bed-mounted camera for your Monoprice Maker Select Plus printer. This is a remix of several other things as noted in the sidebar, modified by adding...

This is a modified design of the Tool Holder for Wanhao D3 / Monoprice Maker Select v2.1 by xenz (https://www.thingiverse.com/thing:2131776). I needed something that attached to the front of my printer since I'm using the SWD3 Kit Z-Axis Rear Mount.

I'm really impressed with this https://www.thingiverse.com/thing:1810943 case for my Pi, so I quickly created a remix to add a mount for my MP Maker Select V2. I carefully centered it as best I could. ...It looks and works perfectly thanks to an...

I needed a Pi case that would snugly fit on my Monoprice Maker Select Plus 3D printer, so when I came across a design that attached to my machine without any hassle, I jumped at the chance to give it a try. ...The design was cleverly crafted as a single...

Mount your Monoprice Maker Select printer and Microsoft Lifecam (Studio or Cinema) webcam perfectly with this custom mount. Place it under the front edge, either centered or offset to fit your needs. Use the original screw from the camera mount for a...

This is an upgraded fixture and nozzle designed specifically for a 50mm blower fan, offering enhanced cooling capabilities compared to the standard 40mm radial fan used on the Monoprice Maker Select Plus. As a work in progress, I'm currently...

Print Settings: Printer: Monoprice Maker Select i3v2 Rafts: No Supports: No Resolution: 0.2mm or better Infill: 100% Notes: Infill is 100% but it's small enough that I don't think infill settings will matter. Post-Printing: Make sure the spring has...

Entry point is 4mm wide, accommodating short PTFE tubing from Monoprice Maker Select Plus printer. This optimized path allows filament to glide smoothly and maintain straightness without curling or kinking. After several prints, tubing easily slid...

I am creating a custom control box ramp for my Monoprice Maker Select 3D printer. To make it more accessible on my smaller workbench, I designed it to rise and angle upwards instead of using a faceplate mod that would require messing with the control...

This accessory is designed to securely store the tools that come with the Monoprice Maker Select Plus 3D printer. It holds all five sizes of Allen keys as well as the print removal tool supplied with the printer. To attach it to the printer, remove...

I was rebuilding my Maker Select V2.1 and realized that I could move the x axis forward and backward by about 3mm. Which is bad, and the only way to tighten it was to tighten a grub nut that was behind a metal plate, a bar... and several other pieces...

I was upgrading my Maker Select V2.1 and noticed that I could move the x axis forward and backward by about 3mm, which is undesirable. The only way to tighten it was to tighten a grub nut hidden behind a metal plate, a bar, and several other pieces...

After my Monoprice Maker Select arrived, I was a bit let down to discover that the filament spool holder included with the printer wasn't large enough to accommodate a full-sized spool. With a 3D printer at my fingertips, the obvious solution was to...

I made a dial indicator mount for my Monoprice Maker Select Plus version 2, which I think is correct. The dial indicator was sliding around on the rails, so this mount uses two #6-32 screws (3.5mm OD) to attach to the extruder stepper motor. I used...

So, I designed one that fits perfectly on top and hangs down the side (check out the photo).\nPrint Settings\nPrinter: \n Maker Select\n \n Rafts: \n Yes\n \n Supports: \n No\n \n Resolution: \n 0.2mm\n \n Infill: \n 10%\n \n Notes: \n It doesn't...

This is the Z height extension for Maker Select Plus (Wanhao Duplicator I3 Plus). These brackets add another 168mm to original 180mm, so the maximum Z height can now reach up to 348mm. In addition to these brackets, you will need the following...

... tools and accessories, including clippers, pliers, hex keys, and SD cards. ...The latest version, V2, incorporates optimized hole sizes specifically tailored for hex keys, while also introducing two dedicated slots for secure storage of micro SD cards.

I fashioned these hasty little supports to affix to the base of my printer after switching to a glass-topped desk. They're designed to accommodate common 33mm adhesive felt pads readily available at most department stores. The resolution and infill...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I created this for my select plus because its home has a low slanted ceiling and otherwise wouldn't fit with a standard size spool. The extruder clears easily when using the maximum print area. You may want to add a binder clip in the rear to keep...

Check out my video here where I walk you through installing Auto Bed Leveling on the stock board using an inductive sensor: https://youtu.be/tL4PZPHHfT0 Also, I created a follow-up video in case the sensor doesn't work with the Arduino Uno as shown...

... and guidance, check the parent project and the grandparent project. Important Note: While I print all of the components on a single bed, it's recommended not to print them all at once - if one piece jams halfway through, it will waste filament.

Print Details: XT (extruder temperature): 245°C BD (bed temperature): 70°C Material: PETG Fan Speed: 100% Overview and Background The project requires the following components: 3528smd LEDs with a 5V power supply USB Cable Soldering Iron Solder For...

I'm currently designing a new build bed for my Monoprice Select Mini v2. I want to be able to use a standard size bed (120mm x 120mm) or a 214mm x 214mm without having to replace the structure that connects to my Y-axis rails. What I have now is...

This is is a work in progress I'm currently in the midst of designing a new build bed for my Monoprice Select Mini v2. I wanted to ability to use a standard size bed (120mm x 120mm) or a 214mm x 214mm without having to replace the structure that...

If you buy a glass bed for your Monoprice Select Mini, print this kit for fix it to the buildplate, it includes: - Z Spacer - 4 Clamps MoonKnight75 and jjonas828 had good ideas but are hard to find, I put them together as a kit in a single model...

I had a common bed temp sensor issue with these printers, which I fixed by repairing the wire and then sought to prevent from happening again. I didn't find exactly what I was looking for, so I decided to make my own. This mod is a re-mix of...

I designed a custom cable support to match my existing articulating camera mount, which is available on Thingiverse under the ID 4161907.