monoprice maker select v2 glass bed 3d models

... or two can be printed simultaneously on the build plate, just barely fitting. Please note that these designs might work with V1 and V2 printers but lack bed levelling cut-outs and may not accommodate unique printer bed attachment methods.

Adapter for Mounting Cobra Fan Duct on Maker Select v2.1 Printer Based on raymnli's design, I had to make some adjustments to accommodate changes in the X-Axis bearing brackets of my Maker Select v2.1 printer. The new brackets have a raised middle...

I purchased a Maker Select v2 in September of 2017 and immediately disliked the loose y-axis wiring that seemed to hang precariously, waiting to be pinched between the table and frame. I discovered a cable chain designed for a Wanaho printer here (a...

I'm trying to eliminate the cumbersome enclosure from my Maker Select V2, but none of the available PSU boxes on Thingiverse are compatible with the Mean Well LRS-200, so I've opted to design a custom one that's lightweight and meets my specific...

I meticulously downsized MoonKnight75's outstanding spacer to accommodate precise 2.2mm glass requirements.

But if you need any offset (ex: glass bed) https://www.thingiverse.com/thing:4624845 No problem with heat bed or insulation material. Printable on the Mini (2 batchs). Reusing orignal screws. You need: - Eight (8) M3 Nuts (dimensions in the design...

But if you need any offset (ex: glass bed) https://www.thingiverse.com/thing:4624845 No problem with heat bed or insulation material. Printable on the Mini (2 batchs). Reusing orignal screws. You need: - Eight (8) M3 Nuts (dimensions in the...

Print Settings Printer: Maker Select v2.1 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Notes: Be sure to use supports to keep the cutout for the fan duct from sagging. How I Designed This =================== Rebuilt raymnli's mounting...

I Added the MOSFET Mod to My Maker Select V2. Two Magnets Hold it in Place, Covered with Electrical Tape. Don't Be Like Me - Skimp on the MOSFET Mod at Your Own Risk! You Think You're Safe Printing PLA, But That Hotbed Temperature is a Hazard...

I designed a clip to keep my glass bed firmly in place on my MP Select Mini V2. My bed was approximately 4mm thick with the glass bed and Buildtak installed. The clip's mouth has ridges to provide a firm grip, which worked well to hold down my glass...

It appears that the spacer on the Monoprice Mini Select's V2 model differs significantly from its V1 counterpart, sporting levers designed to elevate the bed by an impressive 3.5 millimeters, thereby accommodating a PrintinZ pad with ease.

I wanted to try a Y axis mounted camera for my Maker Select V2. I had the "Raspberry Pi Camera Case and Mount for Mini Kossel" already printed out but I didnt like how flimsy it's mounting arms and back were so I drew this up and mounted it to the Y...

To control the fan speed on my Maker Select, I use M106, and to be safe, I default the "Laser Power" to 10 (S10). That way, I can check the laser path to align the item and ensure nothing will be damaged accidentally. Then, using a text editor, I...

I started with the Colossal Mini V2, using this mount in conjunction with the extended bed which evolved into my dual z motor concept V2 mini. I enlarged the bed to 300 x 300mm, added a third rod for additional support and mounted the bearing cup on...

... Print Settings Printer: Maker Select V2 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25% Notes: I printed this design using PETG with a slow setting for the outer layer to achieve an extremely smooth surface, facilitating easy spool-sliding.

I needed an easy-to-remove yet secure mount for my borosilicate glass bed on my MP Select Mini equipped with the 4th Dimension Modifications 120x250mm extended bed. I had the borosilicate glass custom cut to a size of 5 1/8" x 10 1/8". The brackets...

A while back, there was a surge in interest for external 120MM fan shrouds specifically designed for the Maker Select V2. The stock 40mm fan was not doing its job and was actually pulling air in instead of pushing it out. I liked the idea of using a...

--- I'm fed up with disassembling the extruder on my Maker Select V2 and watching those tiny black heatsink spacers fall out and roll away. It's a constant hassle. No more. To solve this problem, I designed a single-piece spacer that performs its...

A custom accessory designed specifically for the Monoprice Select Mini V2 3D printer, created by a maker who posted a photo of their project on the popular online community r/3dprinting. ...Upon seeing the image, a fellow enthusiast requested access to...

This is a dial that replaces the silver one that ships with the monoprice mini select v2.

This is a straightforward filament guide for the Maker Select v2 designed to work seamlessly with the spool holder turned 180 degrees so that the spool rests on the right side. It attaches to the outer two of the four screws located in the top right...

I was examining the filament release lever on my Maker Select v2.1 just a few days ago and observed that one of the sides of the filament insert hole had become misshapen - it looked as though constant friction from the filament against it had worn...

I was looking for a Z-brace kit for my Maker Select v2 and found one here by f0xox that looked simple enough and wasn't overly complicated: https://www.thingiverse.com/thing:3603327. I loved the design by f0x0x but when I printed it and mounted up...

Engineers carefully crafted a specialized filament guide tailored specifically for side-mounted spools to provide precise and reliable performance.

I unwrapped my MakerSelect on Christmas morning, beating the official deadline by a few days - I just couldn't wait that long to get started. This gift was a great addition to my workshop and something I'm excited to work with. This project will...

Replaces Image of Wanhao Rhino IIIP Requires relocating the drag chain bracket, which attaches to the top: http://www.thingiverse.com/thing:1448260 Additionally, the extruder motor needs to be rotated so cable plugs in from behind the printer; this...

These versatile clamps securely hold a 3D printer in place on both the x and y planes. Perfect for mounting on a workbench or shelf, they provide rock-solid stability without obstructing movement. However, it's essential to note that their weight...

This custom spring riser is specifically designed for use with Maker Select printers as well as other extruder configurations that are similar in nature. By compressing the spring by exactly 3mm compared to its standard setting, users can guarantee a...

This initial version works seamlessly with all my spools using the original Maker Select spool bracket. The spool nut is specifically designed for IDs ranging from 48mm to 88mm, and centers the spool precisely when tightened securely. ...The bearing is...

This print is far from polished and only a few test prints were done, it was a necessary print after my Maker Select V2 spool holder broke, so be prepared to source bearings of the right size and do some sanding. I had some 6203Z bearings on hand...