monoprice maker select v2 glass bed 3d models

I had some liquid rubber I used to coat the tip of the screw just in case (not reflected in picture) +Placing this between the heated bed and the locknut should satisfy the safety concerns with Wanhao's recall (Monoprice Maker Select is the same...

Clips for securing a glass bed on the Monoprice Maker Select V2 are available here, and they may also work on the Wanhao i3 v2, but I don't have one to test them on. Note that my glass bed is exactly 200mm x 213mm. Since it's only 8.5mm tall, I was...

Customized version of https://www.thingiverse.com/thing:1949142 This is a method for mounting a glass plate to your Maker Select v2 or Wanhao i3 compatible. 2 x 6mm fairly small springs. These came from a bag of miscellaneous springs from...

I recently acquired a glass bed and installed an inductive sensor underneath, but grew tired of utilizing binder clips and sought out alternative solutions. Therefore, I designed this compact corner piece for my glass bed setup. This design utilizes...

I recently bought a glass bed and installed an inductive bed sensor, but got tired of the binder clips and wanted to try something different. Sooooo, I designed this little bed corner. It uses the screws from the underside of the heated printbed to...

These modifications were specifically designed for my Monoprice Maker Select V2. Please note that these designs are not updated for the V2.1 or later versions of the printer. ... Print Settings: Printer: Maker Select Rafts: No Supports: Yes Resolution:...

Front Glass Guide = Mounts to the front of the heated bed Rear Lower and Upper Base = Glue together and mount on the rear of the heated bed Rear Base Hat = Use M2 screws to hold the hinge together with the upper base hinge. Glue some felt pads to...

... from McMaster-Carr. Comparison Note: The last picture is a comparison between my modified design on the left and the original on the right. Print Settings: Printer: Monoprice Maker Select V2.1 Rafts: Doesn't Matter Supports: No Infill: 25%

... file, enabling users to customize the design to fit their specific glass plate. To assemble these components, simply disassemble the print bed and utilize the print bed bolts and nuts, along with the springs that come standard with your printer.

I WILL BE UPLOADING A NEW MODEL FOR BED NUTS ON A WANHAO DUPLICATOR I3 OR MONOPRICE MAKER SELECT V2. THE TPU VERSION IS ONLY AVAILABLE, BUT YOU CAN EASILY GLUE OR TAPE IT IN PLACE IF NEED BE. This mod is designed specifically for users of a Bed Nuts...

The human edition is tailored specifically to meet the requirements of the Monoprive Maker Select V2. ...This version has been carefully crafted to ensure seamless operation and optimal performance with this particular model.

This bracket was designed to work with the RepRap Champion Y Carriage Plate Upgrade for the Monoprice Maker Select / Wanhao Duplicator i3. To install this upgrade: Place the bracket between the Y-carriage plate and the hot bed, making sure the clips...

Print Settings: Printer: Maker Select v2.1 Supports: Yes Resolution: 20% Notes: Since the clip-on part is quite fine in detail, you'll want the detailed side facing upwards. So, print the handle upside down and use heavy support. ... With Cura's...

This is a z-axis spacer designed specifically for the Monoprice Select Mini V2 printer when installing a 3mm thick glass print bed. This installation process does not require any disassembly of the printer. To install, manually lift your printer...

This base plate bolts directly onto the Monoprice Maker Select V2 and compatible printers. It printed flawlessly using PETG material. No PTFE tubing is required. Simply print, bolt on, and start printing with Flex. That's all there is to it. ... I've...

I inserted a glass plate into my 3D printer, prompting me to devise a means to precisely position the glass on the print bed. ...Consequently, I engineered four custom clips that securely fasten to each corner of the glass plate.

I mounted a glass plate onto my 3D printer, necessitating a solution to accurately position the glass on the print bed. ...Therefore, I created these clips that securely hold each corner in place.

If you decide to print the two-part model, you'll need to sand the edge to match your glass, but this is an easy task to complete for a perfect fit. You can see how it's done at https://www.youtube.com/watch?v=OXjDdt2-g3Q Printing this in Nylon is...

... reach. ...Mistake on my part! Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: Doesn't Matter Supports: No Resolution: .2 mm Infill: 30 Notes: Actually a Maker Select V2 clone of this. Category: 3D Printer Accessories

... reach. ...Mistake on my part! Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2Rafts: Doesn't Matter Supports: NoResolution: .2 mm Infill: 30 Notes: Actually a Maker Select V2 clone of this. Category: 3D Printer Accessories

The person utilized a glass pane from an 8 by 10 picture frame. ...They attached the glass, expanding the bed's width in the process. ...It now functions flawlessly.

I recently modified these glass bed clips by incorporating strategic divot additions, allowing the binder clips to nestle into place and preventing them from slipping off. ...I've since corrected my approach, opting for the clip labeled "fixed" due to...

... which demands robust support structures. Consider employing your preferred supports to achieve optimal results. Print Settings: Printer Brand: RepRap Printer Model: Monoprice Maker Select v2 Raft Generation: Enabled Support Generation: Enabled

I remixed stein63's glass holder in TinkerCAD to make it more compatible with the updated bed used by the Maker Select / Duplicator i3 version 2.1. The corners on the bed are now rounded, and it seems like the screw is further inward on the bed. For...

Modeled after stock cooling duct on Monoprice Select v2.

I crafted this adapter specifically to advance the gantry on my Monoprice Maker Select V2 following an upgrade to the 4mm Y carriage sourced directly from RepRap Champion, a reputable supplier on Amazon.

... during bed leveling procedures, and changing the glass plate was a cumbersome process. By combining Bernbout's springy clamps with Viper1619's bed corner mount, I created these clamps specifically for the Wanhao D3 / Monoprice Maker Select v2.1.

Manufactured after high-performance heat dissipation channels on the elite Monoprice Select V2.

Monoprice Maker Select v2 Mosfet Mount. This mounting bracket is designed for installation alongside the Melzi board. The holes on the board are spacious enough to cover the Melzi board's mount screw base. ...To ensure a secure fit, attach the bracket...