monoprice maker select plus upgrades 3d models

I merged three distinct designs, streamlining their concepts to create a cohesive whole. The resulting filament guide boasts remarkable stability, significantly reducing the annoying clicking sound that often accompanies filament retraction. ...For...

I think there are some design improvements that could be made, but the aesthetic is definitely eye-catching. If you're looking for a more functional design, I'd recommend checking out my other fan cover designs that prioritize airflow. ...The good news...

I really loved the original design except for the cooling fan duct, which I managed to improve significantly. Fortunately, the original post had a step file of the entire assembly that I could easily import into Fusion 360. From there, I made my...

This is a basic enclosure for affordable microSD card extensions available on Amazon. All files are readily accessible, allowing users to make their own customizations, but in case a remix is created, please give credit to the original creator. For...

I reworked the design to ensure that it would fit neatly underneath my bed. ...Additionally, I want to apologize for the poor camera quality in the photos.

A printable replacement for the cup washers on the MPSM. ... I lost a few of the metal ones so replaced them with these guys, work perfectly.

I swapped out the original adapter because it was set up too far forward and not close enough to the build plate for me. The build plate had been adjusted all the way up, but still felt a bit unstable. I decided to replace it with an improved setup...

Required item: 2x Ikea LACK table 4x Neodymium magnets 20mm x 6mm x 2mm 3x Plexi 440 x 440 mm, 3mm thick 2x Plexi 220 x 440 mm, 3mm thick Just print all .stl files and put it all together..

UPDATE: Full-sized SD cards were initially placed too low in the original design, causing them to be difficult to remove from their holders. The updated "V2" has raised the SD cards slightly, making them easy to lift out. I simply wanted a...

I was really impressed by the original design here https://www.thingiverse.com/thing:2006457, so I decided to put my own spin on it. This improved version uses three 608 bearings that let the spool spin smoothly and freely. The spool also sits higher...

Simple enclosures are placed over the LCD screen and control dial openings on the cabinet. ...Utilized after my control circuitry failed and I transitioned to a primary motherboard with a built-in USB port.

This creation was designed using Tinkercad. ... Special thanks to the following projects, both of which are truly exceptional: https://www.thingiverse.com/thing:2353376 https://www.thingiverse.com/thing:2345316

This is a detailed guide on how to install a new heat bed leveling system for a 3D printer using M2 screws and thumb wheels. Here's a step-by-step breakdown of the instructions: 1. Remove existing heat bed clips: The first step is to remove the...

I was inspired by tommytwothousand's design at https://www.thingiverse.com/thing:2163508 to create a filament guide that would seamlessly integrate with my printer and follow its curved edge perfectly. The design aimed to make the guide look like it...

On July 7, 2017, version 2 of the design was uploaded, featuring an updated back mount that clears the housings with ease. However, upon further inspection, it became apparent that the current configuration is too tall and doesn't quite fit as...

Mixed together this robot spinner: https://www.thingiverse.com/thing:2143914 and mz4250's dickbutt, which no longer appears on Thingiverse, to create a unique and functional dickbutt spinner that prints well with supports. ...This project was designed...

This is useful for using a 3d printer like a plotter, just insert a pen in the hole. Print it upside down without scaling it, it does not need supports. ...

I mercilessly miniaturized a carefree figurine of good fortune, then unceremoniously plopped it down on top of a toilet emoji pedestal, all for your benefit.

The relocation of the Extruder Motor enables it to be positioned outside the primary housing and angled at 90 degrees. ...This modification necessitates a Nema17 bracket, extended M3 screws, a lengthened stepper cable, additional M3 nuts and washers,...

I was trying to fine-tune the part I downloaded from Thingiverse, but no program would load the STL file. Every software I used gave me an error message stating that the file was corrupted or simply froze when attempting to open it. In frustration, I...

I created this because printing out an entire side panel can be a real hassle, especially if something goes wrong during the print process and you need to reset for up to 14 hours. Although I designed it specifically for the 4DM Maximus kit, this...

This gadget was crafted with Tinkercad. Its first real design features a dedicated space for the display within my MPSM V1. ...Still, it remains a work in progress.

Create a sturdy spool holder consisting of three distinct components, each requiring a high-quality carbon fiber tube with a diameter of exactly 10 millimeters. ...To ensure secure installation, incorporate two precision-made screws that will hold the...

This versatile wall adapter lets you seamlessly detach and reattach the holder as needed.

I really liked the original design except for the cooling fan duct. Luckily the original post had a step file of the entire assembly. I just imported it to fusion 360, made my changes and here is the finished product. Hope you like it. Original.

I tired of constantly swapping out the micro SD card and fumbling for the adapter, so I created this custom bracket to securely hold an extension cable that connects the micro SD card directly to my printer.

Replacing the Shroud on the Hot-End Heat Sink A replacement part, designed specifically for the hot-end heat sink, is now available. This new shroud allows the original bed sensor screws to function correctly as before. To enhance airflow, a 40mm fan...

I wanted a removable back cover with out having to take the bottom off the machine. I printed this in PETG. Once it was finished. I ran some very small self tapping screws in the bottom back two holes, they act as alignment pins. For the top I...

I liked the idea of the pi camera mounting bracket by stevepax and used it for inspiration to create this one for my GoPro. I ended up angling the shoe instead of the mount itself since it was easier to design. I have included two files, one is for...