monoprice maker select plus upgrades 3d models

https://www.printables.com/model/225717-monoprice-maker-select-v2-wanhao-duplicator-i3-cab includes a handy clip for the cable leading back from the cable chain to keep it out of the way of the bed. ...It's too short for use with AzzA's Z-brace mod, so...

Created a bracket for the rear wire connected to the hotbed of a Monoprice Maker Select V2 to fit the Ender 3 Cable Chain. Rear Connector connects to rear stepper motor bracket, but you will need to get longer M3 bolts. The bracket for the print bed...

These modifications were specifically designed for my Monoprice Maker Select V2. Please note that these designs are not updated for the V2.1 or later versions of the printer. ... Print Settings: Printer: Maker Select Rafts: No Supports: Yes Resolution:...

... during bed leveling procedures, and changing the glass plate was a cumbersome process. By combining Bernbout's springy clamps with Viper1619's bed corner mount, I created these clamps specifically for the Wanhao D3 / Monoprice Maker Select v2.1.

The creator built a custom bracket for the rear wire attached to the hotbed of a Monoprice Maker Select V2, specifically designed to accommodate an Ender 3 cable chain. The rear connector links directly to the rear stepper motor bracket; however,...

This is a thumbwheel designed for use with wingnuts on the Monoprice Maker Select / Wanhao Duplicator I3. Numbers indicate directions to raise or lower the print bed during leveling, helping you remember the correct rotation. Tick marks serve as...

I Convert a standard 54mm Spool to fit seamlessly with the Monoprice Maker Select Bigger Spool Holder v2. Check out this link for more details: https://www.thingiverse.com/thing:1857904 This conversion is ideal for spool holders up to 30 mm in...

Clips on the top of the frame Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Filament: Zyltech PLA green Notes: Print with model orientation, add supports for the top ball. I...

I managed to break the micro-usb socket on my Monoprice Maker Select Mini printer while moving it. Then, I decided to try replacing the socket with a standard panel-mount 'B' socket (the square one), as that would be more durable in the long run. To...

This design works for the Monoprice Maker Select, but it should also work for the Wanhao Duplicator i3. Mount these on the bottom of the x-axis rod carriage, as shown in the photos. You'll need a little glue to hold them in place. I used some...

I chose to relocate the spool holder on my Monoprice Maker Select to the control box, but I wasn't satisfied with the filament routing into the extruder - it kept snagging on my Z braces or rubbing against the top of the frame. Therefore, this little...

I'm excited to share a simple adapter I created to allow standard webcams with a tripod mount to be used with Xenz' "Webcam mount for Wanhao Di3 / Monoprice Maker Select v2.1." To make this adapter, I converted the Webcam Mount and Kahuna's "Tripod...

This LED light bar is specifically designed for use with the Monoprice Maker Select V2.1 3D printer. It replaces the stock fan duct and requires a separate fan setup to be installed. The LED strip used in this project was sourced from Amazon and...

This is a sleek SD card holder that securely attaches to your Monoprice Maker Select atop the control unit. Simply utilize the stock screws designated for the spool holder to screw it in, making installation remarkably effortless. This ingenious...

I saw several custom LED mounts, but none fit perfectly on my Monoprice Maker Select's mounting location. This design combines ideas from other makers' mounts with modifications to bolt onto where the original cooling fan was located. Since I...

I created a cute little Amish Windmill to visually illustrate the extruder's activity for Monoprice Maker Pro (Wanhao D9) Printers, as I couldn't find many indicators available, so now you can see what your extruder is up to in an entertaining way.

The front feet were remixed using the back feet from AzzA's well known design at this URL: https://www.thingiverse.com/thing:921948 Additional Information: This is a rear mounted z-brace for the Monoprice Maker Select V1 and V2, Wanhao Duplicator...

Heated bed stabilizers Cold end fan shroud Bracket for Thorped's fan duct Adjustable BLTouch front mount for Wanhao i3 Mount for BIQU Heated Bed MOSFET Board Print Settings Printer: Monoprice Maker Select v2.1 Rafts: Doesn't Matter Supports: No...

Print Settings: Printer: Monoprice Maker Select v2.1 Supports: Doesn't Matter Infill: 20% Notes: All of those long pieces print vertically upwards, so no support is needed. However, do pay attention to Right_Top.stl and Left_Top.stl since you may...

After researching online to troubleshoot some print quality issues I've been experiencing with my Monoprice Maker Select (Wanhao Duplicator i3 V2.1), I concluded that they might be caused by inadequate cooling. My attempts to find suitable designs on...

Print Settings Printer: Monoprice Maker Select V2 Rafts: No Supports: No Infill: 15% Post-Printing Installation Unscrew and remove the filament spool holder on top of your printer. Run the screws through the new guide's holes, then place it below...

It also uses the mounting tabs from https://www.thingiverse.com/thing:1686028 by mmoore0.Before I got a Prusa printer, I had a Monoprice Maker Select V2 (RAMPS). I really liked parhamdb's original mPSU mounting model because it offered direct chassis...

This modification was designed for the Monoprice Maker Select V2, which should also work with any of the Wanhao Variants. An additional file has been added for those with a 40mm width motor; the original file is intended for the 34mm width motor -...

Original Right side here: https://www.thingiverse.com/thing:1718783 Print Settings Printer Brand: Monoprice Printer: Maker SelectRafts: Doesn't Matter Supports: NoResolution: .2 Infill: 50 Filament: Hatchbox PLA White Notes: A roll of tape...

This is a fan shroud for the extruder's cold end on a Monoprice Maker Select v2.1 (and Wanhao Duplicator i3, and probably others). I designed it to give these benefits:\r\n\r\n* Steer all air from the cold end heatsink upwards and away from the...

I have a Monoprice Maker Select V2 (RAMPS) printer, and I really liked parhamdb's original design because it offered direct chassis mounting, rear plug mount, plenty of space for wiring, and was also visually appealing. Unfortunately, my Sompom...

This is an authentic replacement knob specifically designed to fit perfectly on the Monoprice Select Mini.

**Print Settings** * Printer: Monoprice Maker Select v2.1 * Rafts: No * Supports: Yes * Infill: 20% * Notes: + Frame mount: Easy to print, no special instructions required. + Heated bed mount: Requires printing upside down with heavy use of...

... For Mk2, the "snap-in" feature was removed :). Tinker for yourself: https://tinkercad.com/things/2eSYmyBEkIQ Print Settings Printer Brand: RepRap Printer: Maker Select V2.1 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 20%

I introduce to you, a bolt-on Bowden system I built for my completely (as of now) stock Monoprice Maker Select V2.1 (and this will inherently work for the Wanhao Duplicator I3). Get rid of that moving mass, lessen your vibration, increase your...