monoprice maker select 3d printer v2

Remix of the Filament Feed Base for the Monoprice Select Mini 3D Printer. The feed base broke near one of the screw holes on my Monoprice Select Mini and I tried using the model released by cmniemann, but it didn't work with my printer due to several...

This is a zipped folder containing marlin firmware for a Maker Select V2, also known as Wanhao Duplicator i3, with ramps gen 1.4 board. Here is the kit I used:...

Also offset the hotend about 10mm to the left since for the Maker Select, the hotend is not centered, frequently colliding with the right pillar when pushing the printer to its bed size limits. ... Utilized: 4 x (m3 x 15mm bolts) 2 x (m3 x 20mm bolts)...

Also, offset the hotend about 10mm to the left since for the Maker Select the hotend is not quite centered, and found that it frequently banged against the right pillar when pushing the printer to the limits of the bed size. Used.... ...4 x (m3 x...

I've been wrong before. (Note: My cooling fan has been removed for photo purposes.) I use a Thorpe duct and adapter, so the lower bearing block is shaped to fit and allow for that. You can use 2 Uppers if you don't have that specific lower need. The...

This is a custom filament spool holder crafted to nestle snugly on top of my Maker Select v2, yet it should also fit seamlessly onto the Wanhao Duplicator. I engineered u-grooved wheels that easily accommodate standard 22x8x7mm bearings, which when...

Installing a bolt-on replacement for the single 30mm MonoPrice Mini 3D printer is now possible with ease, thanks to a convenient upgrade. Simply wire in a second fan for dedicated cooling of both the part and extruder. To facilitate quick...

Securely fastening the new component required loosening one of the rail screws at the printer's front, carefully placing the model in position, and then screwing it back into place. ... I utilized screws to anchor the arm and camera case firmly in...

Crafted on a Maker Select V2.1, I chose not to utilize supports. A piece of filament is used in the hinge to keep it assembled. The material is relatively thin, so it doesn't obstruct all light. I employed double-sided tape to attach the top of the...

I'm excited to share another filament feed base for the Monoprice Select Mini 3D Printer, but this one's a brand new creation, not a remix like my previous effort. This fully scripted procedural model was built from scratch inside Blender (2.78) as a...

The maker blocks on my Maker Select v2.1 nullified most popular mods, so I sought alternate methods to mount the stock fan with the Cobra Cooler. While exploring options, I came across a simple mod that met my requirements. The original version of...

This is a simple side mount for a Raspberry Pi v2.1 camera module with a Monoprice Mini Select v2. I could not find an existing design that I liked, so I designed a simple side mount and remixed parts from several designs to: avoid attaching the...

This is a precise replica of the Monoprice Mini Delta.

I've whipped up this handy "stick" to accommodate any spools that won't fit within the Monoprice Voxel printer. ...Be sure to print it either solidly or with an infill of at least 35% to prevent it from snapping when you attach a heavy spooler.

The design should print smoothly on any printer, but I specifically designed it with the most affordable beginner 3D printer available at this price point in mind, which is the Monoprice Maker Select Mini v2. To print the model, you will need to...

This utility holster is specifically designed for Monoprice Select Mini printers, fitting neatly onto either the front or back of the device. It's compatible with both V1 and V2 models, but some modifications are required to get it working with the...

... screws might work as well, but I decided to err on the side of caution. Let's hope it will never trigger accidentally! **Print Settings** * Printer Brand: Wanhao * Printer Model: Wanhao Duplicator i3 V2 * Resolution: 0.2mm * Infill Percentage: 50%

This is a simple side mount for a Raspberry Pi v2.1 camera module with a Monoprice Mini Select v2. I could not find an existing design that I liked, so I designed a simple side mount and remixed parts from several designs to: avoid attaching the...

Here is a 3D printed Filament Guide that attaches to your printer's extruder. This design was inspired by Thingiverse model #1921236 but has been extended to pair perfectly with model #2114888. By attaching this guide, you can significantly reduce...

Naturally, I ordered some replacement switches which I'll link here: https://www.banggood.com/SS-5GL-Micro-Limit-Switch-For-3D-Printer-Accessories-ENDSTOP-RAMPS-1_4-Omron-p-1225333.html?rmmds=buy&cur_warehouse=CN Upon their arrival, I realized the...

... against a short. The cable that comes with the BIQU MOSFET was too short to reach the screw terminal on the MKS board, so you will need to fashion a longer one with dupont connectors or a JST if you're feeling fancy. Category: 3D Printer Parts

I'm a Star Wars fan, so I rewrote this with the correct insignia to make my printer feel at home. This is a remix of the single block X-axis design, and I'll add the double block design as soon as possible. ... Using this shroud requires the cable...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/8cKrNosHN53 Category: 3D Printing

Modified the rugged bracket to pair seamlessly with the 3D printed x-axis bearing blocks featuring integrated belt tensioners. A straightforward tweak was made in Tinkercad. ...Special thanks go out to Thorped, xyzaxis, and Heathicus for their...

... The worn-out bearing noise is gone; my printer now operates smoothly, silently, and accurately once again. STL, SLDPRT, and STEP files are included for your reference. If you're willing, please share your Makes with the community. ... Thank You!

I created a customized version specifically tailored to address the distinct gap size differences between the MP Select Mini V2 and its predecessor, the V1 unit. The main reason for this variation lies in the narrower nut width used on the newer...

If you use a spacer or a different brand of extruder, you may need the stock variant or to modify the design. The stock variant assumes 12mm; this is based on measurements, but I no longer have the stock extruder installed to test. There are some...

To solve this problem, I remixed the blower fan 90 degrees counterclockwise of its original position, providing clearance to build as tall as the printer allows. This cooler is particularly beneficial because it allows the printer to perform well...

A shielded cable with a ferrite core is recommended for connecting the printer's board to the Pi: https://www.amazon.com/gp/product/B003L18RZU/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 Installation instructions: * Place the cable into the 3D...

This side panel fits the Monoprice Select Mini v2 with the SKR 1.4 Turbo board and this board mount.