monoprice maker select 3d printer v2

I constructed a housing from an upcycled table and carved out a slot at the rear for cables. Next, I adapted the UK version of a "Brush Faceplate" for low-voltage cabling - single gang. I trimmed off the bottom and fashioned this bracket to securely...

Biqu Mosfet Holder - Maker Select V2

... you'll need to know how to do most of it on your own. For more information, including firmware changes, see my blog post: https://www.tardigradeoutdoors.com/blog/overhauling-a-monoprice-mp-select-mini-v2-mpsm-v2-with-skr-14-board-octoprint-and-more

This 3D printed camera mount is engineered to seamlessly attach itself to the Monoprice Maker Select V2's sturdy base plate, effortlessly gliding back and forth without compromising the print bed in any way. ...The ingenious rotating base and arms were...

I designed a thumb screw cover for the bed leveling wingnuts that come with the Maker Select v2 from Monoprice, using what I had on hand since I didn't have any extra M3 nuts. The stock thumb screws fit perfectly into this print with my printer's...

... from McMaster-Carr. Comparison Note: The last picture is a comparison between my modified design on the left and the original on the right. Print Settings: Printer: Monoprice Maker Select V2.1 Rafts: Doesn't Matter Supports: No Infill: 25%

I crafted a filament guide tailored specifically for a spool that's mounted directly on the Maker Select V2.1 printer.

A custom accessory designed specifically for the Monoprice Select Mini V2 3D printer, created by a maker who posted a photo of their project on the popular online community r/3dprinting. ...Upon seeing the image, a fellow enthusiast requested access to...

After adding a glass bed and upgrading the thicker aluminum Y carriage on my Monoprice Maker Select v2, I discovered that the thumb screws remained loose after adjusting the Z end-stop. To address this issue, I decided to upgrade the springs for...

This resolved the issue and the fan now sits flush to the heatsink. -- For those of us with a Maker Select V2 (and maybe other models as well), it's always a PITA when you have to disassemble the extruder, and those little black heatsink spacers fall...

Print Settings Printer: Maker Select v2.1 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Notes: Be sure to use supports to keep the cutout for the fan duct from sagging. How I Designed This =================== Rebuilt raymnli's mounting...

Adapter for Mounting Cobra Fan Duct on Maker Select v2.1 Printer Based on raymnli's design, I had to make some adjustments to accommodate changes in the X-Axis bearing brackets of my Maker Select v2.1 printer. The new brackets have a raised middle...

The Creator Stand is a compact attachment that plugs directly into the Maker Select V2 Control Panel, designed to securely store both the supplied Spatula Tool and Diagonal Wire Cutters.

Print Settings: Printer: Monoprice Select Mini 3D Printer Rafts: No Supports: Yes Infill: 100% Notes: While resolution isn't crucial for a functional part, printing at 100% infill will enhance the component's durability. ...This is the fourth iteration...

This custom spring riser is specifically designed for use with Maker Select printers as well as other extruder configurations that are similar in nature. By compressing the spring by exactly 3mm compared to its standard setting, users can guarantee a...

... Print Settings Printer: Maker Select V2 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25% Notes: I printed this design using PETG with a slow setting for the outer layer to achieve an extremely smooth surface, facilitating easy spool-sliding.

I purchased a Maker Select v2 in September of 2017 and immediately disliked the loose y-axis wiring that seemed to hang precariously, waiting to be pinched between the table and frame. I discovered a cable chain designed for a Wanaho printer here (a...

I'm trying to eliminate the cumbersome enclosure from my Maker Select V2, but none of the available PSU boxes on Thingiverse are compatible with the Mean Well LRS-200, so I've opted to design a custom one that's lightweight and meets my specific...

I Added the MOSFET Mod to My Maker Select V2. Two Magnets Hold it in Place, Covered with Electrical Tape. Don't Be Like Me - Skimp on the MOSFET Mod at Your Own Risk! You Think You're Safe Printing PLA, But That Hotbed Temperature is a Hazard...

I've broken down the massive components into smaller pieces that can snugly fit within the Monoprice Select Mini's build area. The build process itself is incredibly robust, thanks in part to my relative inexperience with 3D printing - this was only...

I was looking for a Z-brace kit for my Maker Select v2 and found one here by f0xox that looked simple enough and wasn't overly complicated: https://www.thingiverse.com/thing:3603327. I loved the design by f0x0x but when I printed it and mounted up...

This kit is our cutting-edge design that supersedes the previously popular PLUS 3D Printer Z-brace kit. The new kit features a rear-mounted configuration, providing superior access to the print platform. In our kit, we utilize ball joints to...

I wanted to try a Y axis mounted camera for my Maker Select V2. I had the "Raspberry Pi Camera Case and Mount for Mini Kossel" already printed out but I didnt like how flimsy it's mounting arms and back were so I drew this up and mounted it to the Y...

This is a straightforward filament guide for the Maker Select v2 designed to work seamlessly with the spool holder turned 180 degrees so that the spool rests on the right side. It attaches to the outer two of the four screws located in the top right...

I acquired a Mono Price Maker Select 3D printer, essentially a clone of the Wanhao Duplicator 6 3D printer. I didn't want the tools lying around, so I created a neat little stand for the scraper and other tools that came with it. It appears they ship...

This clip securely attaches to the base plate of the Maker Select V2, allowing you to capture those smooth time lapses everyone strives for. Feel free to share your suggestions, show your appreciation, and spread the word with your friends - this...

--- I'm fed up with disassembling the extruder on my Maker Select V2 and watching those tiny black heatsink spacers fall out and roll away. It's a constant hassle. No more. To solve this problem, I designed a single-piece spacer that performs its...

... only the top part touches the spool, not the outer edges. I also added a slight lip to the end. Kudos to toastedsilicon for creating an outstanding design! Print Settings: Printer: Maker Select Rafts: No Supports: No Resolution: 0.2 mm Infill: 25%

A while back, there was a surge in interest for external 120MM fan shrouds specifically designed for the Maker Select V2. The stock 40mm fan was not doing its job and was actually pulling air in instead of pushing it out. I liked the idea of using a...

I wanted to repurpose my 3D printer as a laser engraver to create unique Christmas gifts this year, after discovering a powerful 500mW laser module at Amazon for $39 that included everything I needed: driver, fan, and safety glasses. I recently...