mono x 3d models

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a...

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Hello there, this is a support to let you to drain your resin bottle in to the VAT. It could be used with plate installed or not, and also with different size of resin. I think is very useful and in different situations. ...

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

this is tight, you will need a hair dryer to heat up the plastic (pla) then slide it on all the way back, it was also designed to fit snug with the build plate so it doesn't shift when screwing it down after each print.

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

you don't have to worry if your printer has enough resin anymore. ...works with original Anycubic resin bottle.

Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the 3...

Works well. This is the final version where i made improvements over the original designs. It now has 10mm fillets on all of the corners and the lid cutout is angled 10 degrees to sit level when in use + .1mm larger so the lid will slide in a bit...

Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the...

R_E_R_F (Nono X) and R_E_R_F-Mono, stl files based on the New AmeraLabs city and updated by Errandir || 3DSS of the Atlas community Join us on discord : https://discord.gg/qmCk8Dbm Set the base time 1= base time 2= base time +0.4s +.4s for all the...

... drains.  There are two files.  One is for the stock build plate.  The other is for a build plate that has a flex plate added. ... The stock version should be printed at 39mm x 33mm x 56mm The Flex Plate verison should be printed at 39mm x 31mm x 56mm

If you use a flexible steel plate flex bed on the Photon X 6K, then you cannot calibrate the Z-Axis anymore, because the new flex bed sticker adds 2.7mm to the bed. This new flag will compensate for that. This flag is to adjust the z limit switch...

After the platform is completely cooled, remove the model,

This part can be screwed on top of the buildplate using the already existing threads. ...It is meant as a guide to drill evenly distributed holes for magnets as a replacement for the flexplate magnetic sheet

installing an Heater in the Anycubic MonoX I have to place the Temp sensor somewhere... ...so I had the Idea to place it on Top of the WiFi Antenna

Drip Bracket for draining the Platform. The Cover can still be on the printer. The Idea is, that most of the resin will be back in the vat. I printed the bracket with and without infill (15%). For stability I would recommend to to do no infill. ... ...

Quick fix. Printed in ABS at .2 layer height. 20% infill. ...Beats using a wrench.

EDIT: I reworked the file to be indexed. If your printer runs #1-8 in a different pattern, let me know and I can try to create the layout for you. I was disliking the longer run time RERF prints for the MonoX to, so I decided to create my own. My...

for just corvering and store vat with resin inside without damage bottom fep you can also print the stacking system for further vats you can glue or juste assemble parts

This is a drain bracket similar to https://www.thingiverse.com/thing:4627080. I tried to find it to give remix credit but it didn't show up. I printed mine in Ultem. ... I recommend using something at least as strong as ABS.

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Based on the original and awesome design by @samuelemarazzita. ...I printer the original, but my resin vat tilted backwards, damaging the FEP, which made me realize that if I added some support on the back it would make it sturdier.

<p>fits tight, you might increase size by 1%. ...If you have elephants foot, it will need to be trimmed.</p>

Blocks to hold the cover in place! if you use an optional seal or not....hold cover in place.. ... The inspiration comes from my Anycubic Wash&Cure Plus...

Changes to the Original: - Length and Width overall so if you stack another VAT on top the "feet" line up - Larger "lip" for the bottom of the lid so it fits more securely inside the VAT with almost zero play - Shallower "lip" for the bottom of...