mono x build plate 3d models
665588 3d models found related to mono x build plate.
thingiverse
Replacement for the top knob of the Anycubic Photon Mono X resin printer (also for Mono X2 and Mono X 6K). This is the knob that holds the platform in the Z axis arm. Also useful for any other M8 knob (but check the length of the screw needed). ... ...
thingiverse
... of http://www.thingiverse.com/thing:50437, designed using Customizer! ...Access it at http://www.thingiverse.com/apps/customizer/run?thing_id=50437. To build this item, you need to set Block Width to 25mm, Block Height to .3mm and Block Length to 25mm.
cults3d
heres how: ---in Visual studio code ---click on your keyboard CTRL and F ---type or copy and paste: #define INVERT_E0_DIR ---change true TO false ---should look like: #define INVERT_E0_DIR false Included in this version of marlin firmware: Games:...
thingiverse
Handle to be clipped on underneath Mega Zero build plate
thingiverse
Bambu Lab wall mounted build plate holder. ...Can hold up to 4 plates.
thingiverse
Glass Build Plate Repository with Capacity for Plates Up to 4 Millimeters Thick
cults3d
A simple spacer designed to fit around the springs and washers underneath the build plate. I locked my plate down because I use a 3d touch sensor and don't need the manual adjustment anymore. Designed for my Anycubic Mega X but probably works for...
thingiverse
But you may need to buy one or two more spring and screw sets for the back corners as these clamps are designed to be used on the corners of the build plate. Make sure to use high temperature resistant filament as the build plate can reach...
thingiverse
This remix include: -prolonging the hanger to better support printing bed - it should stop rotating around the screw - it was 2 mm short in my printer -adding cut off so the screw lay flat on bed (earlier it was partially on hanger partially on...
thingiverse
Works well. This is the final version where i made improvements over the original designs. It now has 10mm fillets on all of the corners and the lid cutout is angled 10 degrees to sit level when in use + .1mm larger so the lid will slide in a bit...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330
thingiverse
Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330
cults3d
Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the 3...
thingiverse
Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330
cults3d
you don't have to worry if your printer has enough resin anymore. ...works with original Anycubic resin bottle.
thingiverse
Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the...
thingiverse
Mk12 MakerBot Replicator 2 XLR8 3/16 Glass Build Plate Conversion Plate Made Based On Official Design The following item is made based on the original design that comes with P3D's glass build plates. ...To view more information about these build plates...
thingiverse
A little right angle bracket that can be taped to the stage to make reattaching the magnetic build plate quick and easy. The bracket has a 16 mm x 15 mm base (horizontal surface) and is 9 mm tall. ...I used 3M clear double sided tape to attach the...
thingiverse
The MakerBot AL Build Plate is designed for use with R1, R2, and R2X models. This platform features a magnetically-attached glass/acrylic/ceramic/porcelain surface measuring 312mm x 172mm, which is square cut without contours or steps to provide...
thingiverse
The build plate now has an angled corner, which allows for better resin drainage during the printing process. Additionally, I've trimmed the design slightly to ensure a snug fit on the Mars build plate. ... This redesign still utilizes the same screws...
thingiverse
To address this issue, support rollers are added to the underside of the build plate on both sides of the X-axis 2040 extrusion. The necessary materials include two replacement screen door rollers with a bore that fits a 10-32 screw as an axle, two...