monitor stand 3d models

I have a standing desk riser that lifts my monitors when sitting and needed something to keep my third monitor at the same height. Also works by itself for monitor stands that cannot raise or lower.Printed base on its backside so supports were not...

This monitor mount attaches to the back of existing monitors that have the 100 mm square hole pattern for mounting monitor stands with some height adjustability. ...This is a great idea if you need a decent webcam but don't want to spend more than $30...

Giving additional height of 80mm of the monitor. ...There are 2 files uploaded, 1st is for the front stand and 2nd is for the rear stand. ...As the width of the stand is different at front and rear.

This is monitor stand I made for my monitor, I printed it in PLA+ with a 27 inch monitor on it for 8 months now. ...I do wanna stress though that your mileage may vary depending on print material used</p>

This is another option for legs of a monitor stand, this is meant for a sturdier setup, you can print 4 and this can hold the monitor + speakers, laptops, desktop or monitor. ...You just need to use it in the corners of a wood plank to make sure all the...

Simple stand for portable monitors. ...Features:Universal design for <14mm thick monitors *Case required*Legs are thick enough to avoid any wobbleFree up space below your monitor (14cm)Use it as a cable organizerPrinted in PETG, 3 perimeters and 20% hex...

I chopped off the side support arms a little to make the stand more compact and reduced the tilt angle so that the monitor stands a little more upright. Thanks to Jonny_O for sharing the original thingy. Shapr3D was used for this. ... This is a...

Never use wobbling monitors again!This is a simple design I created using Openscad just to avoid any wobble in my suspended monitor, whose arm is attached to the desk.I suggest you print these in pairs and use it at the sides so that your monitor...

This is a simple monitor stand legs you can screw to a piece of wood to create a minimalistic piece for your desk.

Short monitor stand for Samsung SF350 Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: Off Supports: None Resolution: 0.3mm Infill: 40%

My Trusty KRK RP6 Monitor Stand Setup Requires a Few Essential Components Including 8 mm Rods and M3 Screws and Nuts to Get Started.

I am testing out Customiser creation with this thing. ... I made a version of the monitor stand leg by Austin02 that should be fully customisable.

This is yet another monitor headphone stand.. There are 3 versions. Version 1 - Simple Version 2 - Partially Rounded Version 3 - All edges rounded Print Time - Avg. ...1hr 20min

The ergonomic monitor stand boasts an impressive 3-inch (75mm) height adjustment and a closed width that measures approximately 270mm x 170mm.

Place the monitor stand at a comfortable height and add extra space to accommodate storage devices such as a 2.5-inch hard drive.

A drawer-equipped monitor stand is crafted by Borna Noavaran Pouya Company, Limited. ...Learn more about this design at www.borna3d.com.

I needed a monitor stand as I lost my old one so I added more support and a little personal touch to it. ...Also made it 100x100

Hello everyone. ... Here is a stand for the Benq EW2440 monitor. Simple design, with front and rear grips. ...A hole in the middle to pass the cables.

Quad monitor stand features an ideal post for mounting a shelf atop, providing a seamless space to showcase your Sonos system.

Create a stand specifically designed to hold an Acer H236hl display on both sides. ...Print two separate units, one for each side of the monitor.

The stand is loosely based on my original design, I made it for a generic 20x18 monitor base (it is 20cm wide and 18cm deep)

This sleek vertical monitor stand uses a sturdy 2.5cm section of PVC tubing as its foundation, perfectly supporting a 19-inch screen and delivering exceptional performance.

I haven’t tried it with any other models of monitors, but mine is 10 mm thick, so I designed the gap to be 11 mm and it worked out pretty well. One thing I have discovered since making this is that it was prone to sliding around, but I’ve since put...

I only want the monitor for Microsoft Teams while I'm working (or music playlists when I'm not), so I decided I only need a small monitor - So I opted to just get a portable monitor and make a stand for it - Seen as though the monitor won't exactly...

In STLs you can find all component to assembly this stand for monitors with 100x100 VESA mount and accesories as exension cable holder or Intel ComputeStick holder. Size of monitors is not so important, because you can use it for smaller or larger...

Here are two different stands for a vertical monitor stand, one is open ended so that it can slide onto almost any monitor 17mm and under width wise. One closed ended for a more finished look.I am using mine with a 21.5in acer monitor with the...

... much space. This should work with any monitor stand that has 33mm tall arms and uses M5 mounting bolts. The extension I have in mind is 60mm long, 20mm wide, and 33mm tall. ...However, these dimensions can be adjusted using the SCAD file attached.

The stand allows you to install a monitor and other interior items on it. You can also remove the keyboard under it. Suitable for boards in section 18х200 mm. Printing bracket dimensions 211х100х20 mm The size of the board in the photo is 800 mm....

Monitor stand legs fitting for an IKEA Linnmon table so you can put a monitor stand onto it. ...For those that like things in ultrawide.</p><p>&nbsp;Requires an 18mm thick wooden board that is as wide as the table and some M4 Spax screws.</p>

Minimalistic monitor stand Here are some nice feet of a monitor stand. I put a 40 cm x 15 cm glass between them. ... Dimensions of the hole for the glass: 5 mm x 150 mm External dimensions: 155 mm x 107 mm x 20 mm