molle phone mount 3d models

I am absolutely terrible at OpenScad but here is an attempt. I edited it from this. ... Category: 3D Printing

Customized version of https://www.thingiverse.com/thing:3075053 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3075053

<p>Držák zásuvný pro GoPro držákové nástavce:</p><p>K sestavení držáku je potřeba 4x M2x10</p>

Wanted a secondary phone mount for my Schwinn IC4 so that I can connect the IC4 to my phone for power output while watching workout videos on another device. Couldn't find one that already exists so I remixed an STL in Fusion 360 to mount the phone...

This is modification of the well known dash tray separater design modified to mount a generic ball joint phone holder. ... The ball diameter fits generic or phone specific mounts (not included) with a 17mm ball joint.

A very adaptive phone mount for various smartphones. ...Comes with a duct tape base, but can also be used with [Ball joint phone mount](https://www.thingiverse.com/thing:1035943). ...

This was a fix for commonly found budget phone mounts where phones can be removed from the base mount. The retaining tab failed, this replaces it. ... May require support.

I just designed a phone mount base plate to install any phone mount in my KIA XCeed. The base plate is installed between the console and the heater. ... The plate is printed with PLA

Featuring a 3D printable design, this bike stem phone mount is specifically created for use with the HTC Desire 510.

Simple Wall Mounted Holster For you phone that lets you plug it in while it is in the holder

Phone mount Pajero 2012 Prinetd with ABS nozzle temp - 240C Bed temp - 110C Ambient temp - 38-42C By Talor.K

bike handlebar phone mount with quick release gopro attack remix of https://www.thingiverse.com/thing:4717208

Daniel Kim's phone mount was transformed by me to seamlessly integrate with every single one of my GoPro accessories.

A custom mount secures a Cisco phone on a wall, created specifically for use at my educational institution.

My Ford has a cubbyhole in the dash. ...I created a phone mount that fits in this hole.

Its a wall mount for moto g power. ...Should fit any phone that is under 7.4in.

I upgraded Daniel Kim's phone mount to seamlessly integrate with every single one of my GoPro accessories.

Wall mount phone holder with a wooden pattern.Used filament: SUNLU PLA WOOD - low temp.

The "Mount Phone Clamp" from "Modular Mounting System" by HeyVye is a little small, if you have insert you phone in a booklet phone case. So I enlarged the clamps a little bit. ...They are still compatible with the rest of the "Modular Mounting System".

This is a simple mount for the phone holder for the MotoCaddy, slide it in and use a RAM mount or similar to hold the phone.This is just the mount, not the other arms and phone holder peaces. NOTE: Apparently not a snug fit on the 2022 model, from...

Simple and easy to print in place phone mount. The two gopro mounts allow it to mount it horizontal or vertical. I like to use the small tripod from gopro. Just use a rubber band like shown in the pictures to keep the phone in place. Made for...

This is a simple mount for the phone holder for the MotoCaddy, slide it in and use a RAM mount or similar to hold the phone.This is just the mount, not the other arms and phone holder peaces. NOTE: Apparently not a snug fit on the 2022 model, from...

This is a mount for using a phone on a manfrotto tripod, originally meant for a camera. The mount is adjustable and is able to accommodate phones of different width. Rubber bands do need to be used to keep the phone from slipping out of the mount.

I designed this mount to replace the Bontrager Insta Mount that holds the cell phone to the bike with double faced tape because it fell off more than once and I did not like the extra mount permanently attached to my phone case. With this mount; I...

Phone mount for my F150. Bolts on, as I didn't like the vent-mounts. ...Printed in ABS as PLA melted quite quickly.

A small mount for your phone that can be placed on top of your laptop. Designed for MacBook Pro and iPhone, but can also with other laptops and phones. ...Use at your own risk.

I made this phone wall mount for a Samsung s21 fe. ...You can edit it to fit your phone if you want, I have 2 versions one with a screw holder and one to use a sticky tack.

A tightening phone mount attachable to the middle portion of standard bike handles (diameter=1in) for roughly iPhone 6-sized phones (5.5in x 2.5in x 0.3in).

A small mount for your phone that can be placed on top of your laptop. Designed for MacBook Pro and iPhone, but can also with other laptops and phones. ...Use at your own risk.

Did a phone mount that works for the 1"-ish hole in my Fitness Gear power rack with my iPhone (Pro Max size). ...Should work for quite a few phone models.